Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
I NS T AL L AT I ON M A N U A L
Removing 1 or more of these eyelets allows the door to fall to the desired level.
Proceed as follows when adjusting the door handle:
Ø
Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 8a
EA
(Instyle and Prostyle
clamped.
Ø
Adjust the pin.
Ø
Tighten the 2 hexagonal nuts again.
Ø
Test the sealing of the door (see the start of this paragraph).
Ø
Repeat this process if the result is not satisfactory.
9.4 Glass pane(s)
•
Avoid damage when removing/fitting the glass pane(s);
!Caution
•
Avoid/remove fingerprints on the glass pane(s) because these burn in.
Use the supplied pane window cleaner to remove fingerprints/dirt on the glass pane(s).
Tip!
9.4.1 Disassembly of glass pane in door(s)
To remove the glass pane in the door(s) follow the instructions below:
(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle applianc: see Appendix 2, fig. 10).
When you install an Instyle or Prostyle 700
!Caution
on the other side of the appliance.
Ø
Open the door.
Ø
Lift the door out by first sliding it upwards, then tilt it slightly forwards and allow it to lower.
Ø
Place the door on a flat surface.
Ø
Remove the nuts from the strips.
Ø
Remove the strips.
Ø
Lift the glass pane out. The pane seal is then also taken out.
•
When replacing the glass pane always replace the seal in the door (= seal between the glass pane and the
Tip!
door).
•
Check the door sealing cord and replace if necessary (see paragraph 9.3).
9.4.2 Assembly of glass pane in door(s)
Assemble the glass panes in the door(s) according to the steps described in paragraph 9.4.1 'Disassembly of glass
pane in door(s)' but in reverse order.
(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle applianc: see Appendix 2, fig. 10).
Assembly of the door(s) is somewhat different.
!Caution
Proceed as for assembly of the door(s):
Ø
Bring the hole at the bottom of the hinging part of the door exactly below the lower pin.
Ø
Slide the door up. The pin slides into the lower hole.
Ø
Bring the hole at the top of the hinging part of the door exactly above the upper pin and allow the door to lower.
The pin slides into the upper hole.
Ø
The door is now assembled.
•
Do not fasten the bolts too tight to avoid breaking off and/or stripping: overtightening will cause breakage.
!Caution
•
Place the glass pane (including new pane seal) with the logo to the bottom right.
9.5 Frames
The appliances can be fitted with various frames. The frames are adjustable in depth and can be fitted so they are
parallel to the door.
The installation depth of the appliance depends on the selected frame (see Annex 2, fig. 1)!
!Caution
When assembling the frame proceed as follows:
First remove the door before assembling the frame.
Tip!
In-built frame (no frame):
Ø
Remove the 4 pre-assembled bolts/nuts (see Appendix 2, Fig. 11).
Ø
Slide the frame over the stove into the desired position (see Appendix 2, Fig. 12).
Ø
Fasten the 4 bolts and nuts (the bolts on the inside, the nuts on the outside of the appliance)
(see Appendix 2, Fig. 13).
Ø
Fasten the 2 bolts and nuts on top of the appliance (see Appendix 2, Fig. 13).
700) and 8b (Instyle and Prostyle
EA
Tunnel: Follow the instructions below. Then repeat these instructions
EA
700 Tunnel)). This pin ensures that the door is tightly
UK
Advertenties
Hoofdstukken
Inhoudsopgave
