Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6. The induction hob makes a low humming noise when used on a high heat setting.
This is caused by the technology of induction cooking: This is normal, but the noise should quieten down or disappear
completely when you decrease the heat setting.
7. Fan noise coming from the induction hob.
A cooling fan built into your induction hob has come on to prevent the electronics from overheating. It may continue to run
even after you're turned the induction hob off: This is normal and needs no action. Do not switch the power to the
induction hob off at the wall while the fan is running.
8. Pans do not become hot and appears "
The induction hob cannot detect the pan because it is not suitable for induction cooking. The induction hob cannot detect
the pan because it is too small for the cooking zone or not properly centred on it: Use cookware suitable for induction
cooking. See section 'Choosing the right cookware'.
Centre the pan and make sure that its base matches the size of the cooking zone.
9. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is
displayed (typically alternating with one or two digits in the cooking timer display).
Technical fault: Please not down the error letters and numbers, switch the power to the induction hob off at the wall, and
contact a qualified technician.
Failure Display and Inspection
If an abnormality comes up, the induction hob will enter the protective state automatically and display
corresponding protective codes:
Problem
Possible causes
The appliance
Break in power supply
does not work
During heating,
Delay off timer activates.
the unit stop work.
No pan or pan unsuitable
U
E2
Input power too low
Input power too high
E1
F3
Thermistor of coil short circuit.
F4
Thermistor of coil open circuit.
Too high temperature
E5
of IGBT thermistor.
Too high temperature
E3
of coil thermistor.
F9
IGBT thermistor short circuit
FA
IGBT thermistor open circuit
The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.
Installation
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid
larger deformation caused by the heat radiation from the hotplate. As shown below:
L
H D
X
B
X
Under any circumstances, make sure the Induction cooker hob is well ventilated and the air inlet and outlet are not blocked.
Ensure the Induction cooker hob is in good work state. As shown below
Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 600mm.
!
EKI604-2
" in the display.
Please check the main power is normal; if the leakage protection switch is off; if there is a blown fuse,
replace it with a new one; if the main power is normal, check if the plug is connect with socket
appropriately; If the hob is wire connection type, disconnect the power, check if the wire is loose;
disconnect the power, check if main plug is off; Exclude above reasons, should be appliance fault, send
it to service center for repairing.
Please check if set delay off function. If set delay off function, the unit will stop once delay off time out.
No pan, please put proper pan. PCB synchronization or drive circuit fault, please send the
appliance to service center for repairing.
Low voltage, voltage of the main power is less 180V. Please check if voltage of the main power is normal.
Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please send the
unit to service center for repairing.
High voltage, voltage of the main power exceeds 250V. Please check if voltage of the main power is
normal. Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please
send the unit to service center for repairing.
Sensor of coil thermistor connection error. Or detection part of PCB coil thermistor failure,
send to service center for reparing.
Too high temperature of IGBT thermistor, air outlet is blocked. Open air outlet, re-start the unit. If still
unsolved, it is possible that cooling fan connection error, cooling fan damaged, or drive circuit of fan
failure, send to service center for repairing. IGBT temperature sensor open circuit /short circuit.
Temperature detection part of PCB IGBT failure, send to service center for repairing.
Too high temperature on induction glass surface, please check if there is no water in pan. After
treatment, connect with power again. If still unsolved, it is possible that sensor of cooktop failure, send to
service center for repairing.
Senor of IGBT thermistor connection error. Or detection part of IGBT PCB sensor failure,
send to service center for repairing.
W
SEAL
X
A
What to do
L(mm)
W(mm)
H(mm)
590
520
66
Version 3-2023
D(mm)
A(mm)
B(mm)
60
560
490
X(mm)
50 min
Page 7
Advertenties
Inhoudsopgave
