Advertenties
Mode
Display
Low speed
High speed
NOTE: Be sure to select the ball mode when you
inflate a ball using a sport ball needle. If other mode is
selected, the inflation cannot be performed properly.
NOTE: Be sure to select the low speed mode when
you inflate an object using an English valve adapter. If
other mode is selected, the inflation cannot be per-
formed properly.
Lighting up the front lamp
When you turn on the tool by pressing the main power
switch, the lamp lights up. When you turn off the tool by
pressing the main power switch, the lamp goes out.
► Fig.6: 1. Lamp 2. Main power switch
CAUTION:
Do not look in the light or see the
source of light directly.
NOTICE:
When the tool is overheated, the lamp
blinks. Turn the tool off and let the tool cool down
fully before operating the tool again.
NOTE: Use a dry cloth to wipe the dirt off the lens
of the lamp. Be careful not to scratch the lens of the
lamp, or it may lower the illumination.
Storing adapter
The adapters can be stored in the adapter holder of the
tool. Insert the sport ball needle into the Presta valve
adapter before attaching them to the adapter holder.
► Fig.7: 1. Sport ball needle 2. Presta valve adapter
3. Adapter holder 4. Tapered adapter
Storing hose
The hose can be attached to the hose holder of the tool.
► Fig.8: 1. Hose holder 2. Hose
Air release button
NOTICE:
While the English valve adapter is
attached to the tool, the air does not go out even
when you press the air release button.
When the object is inflated too much, press the air
release button to release air.
► Fig.9: 1. Air release button
Purpose
Adjustable
pressure
range
To inflate
35 to 1,110
objects in low
kPa
speed
(5 to 161 PSI)
To inflate
objects in
high speed
OPERATION
NOTE: The standard adapters vary depending on the
country.
Using the English valve adapter
NOTICE:
Be sure to select the low speed mode
when you inflate an object using an English valve
adapter. If other mode is selected, the inflation can-
not be performed properly.
1.
Insert the English valve adapter into the air chuck.
2.
Attach the English valve adapter to the valve stem
while opening the English valve adapter.
► Fig.10: 1. English valve adapter 2. Air chuck
3. Valve stem
3.
Turn on the tool.
4.
Inflate the tire by pulling the switch trigger while
checking the status of the tire.
NOTICE:
When using the English valve adapter,
the pressure gauge will not display an accurate
value due to characteristics of the valve. When
inflating a tire, do not use the value on the pres-
sure gauge, but inflate it by checking the status
of the tire.
If the tool stops before the tire reaches the
desired air pressure, adjust the pressure value,
and then inflate the tire again.
Using the Schrader valve adapter
1.
Attach the air chuck to the valve stem.
► Fig.11: 1. Valve stem 2. Air chuck
2.
Turn on the tool, and then set the pressure value
appropriate for the tire using the pressure gauge.
3.
Keep pulling the switch trigger until the tool stops.
The tire is inflated with the specified pressure.
Using the Presta valve adapter
1.
Loosen the locking nut on the valve stem.
► Fig.12: 1. Locking nut
2.
Attach the Presta valve adapter to the valve
stem, and then attach the air chuck to the Presta valve
adapter.
► Fig.13: 1. Presta valve adapter 2. Valve stem 3. Air
chuck
3.
Turn on the tool, and then set the pressure value
appropriate for the tire using the pressure gauge.
4.
Keep pulling the switch trigger until the tool stops.
The tire is inflated with the specified pressure.
5.
Remove the air chuck and Presta valve adapter,
and then tighten the locking nut.
10 ENGLISH
Advertenties
