Inhoudsopgave
Advertenties
III BASSINET ASSEMBLY The assembly of the bassinet should begin with inserting the loose part of the frame (G) into the
slots in the bassinet (F) (FIG. 8). Make sure the latches are secured (FIG. 8A). Then fasten the zip fastener on the perimeter
of the mounted part (FIG. 9). Adjust the rod under the bassinet with straps and secure with snaps (FIG. 10). A complete
bassinet is shown in Figure 11. The bassinet can now be attached to the buggy frame (you will hear the sound of the locks
on both sides of the buggy) (FIG. 12).
WARNING! THE BASSINET CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
NOTE! When the child starts to sit independently, attach an
additional harness to the attachment points shown in the
picture (Fig. 41).
IV ASSEMBLY OF SAFETY BAR, HOOD, FOOTMUFF The safety bar (E) can be used in both the bassinet and the pushchair
function. Insert the tips of the safety bar in the corresponding slots until you hear the locks on both sides (FIG. 13).
Start the installation of the hood (I) from inserting plastic clips in the fastenings in the bassinet/seat frame (FIG. 14).
Proper protection is indicated by a quiet click. Lastly, secure the hood with Velcros (FIG. 15) and wrap around the tilt
angle adjustment lever (Fig. 16).
Start the installation of the footmuff (J) from pulling it as shown in Figure 17. Wrap the ribbons on both sides of the safety
bar and secure with snaps (FIG. 18). Wrap the free end of the footmuff around the safety bar and secure with buttons
(FIG. 19). Additionally, attach both ends of the footmuff to the shell (FIG. 20).
V CONVERTING THE BASSINET INTO THE SEAT To convert the bassinet into the seat, you must first pull out the belts on
both sides of the shell (FIG. 21) and under the footrest. Connect the ends of the belts behind the back, under the seat
and the footrest (example Figure 22). Properly fastened belts should look as shown in Figure 23 (seat angle control
method described in section VIII).
VI MOUNTING THE BAG, MOSQUITO NET AND RAIN COVER The MOOV stroller set includes: bag (M), rain cover (N) and
mosquito net (O). Use the silicone hangers to hang the bag on the parent handle (FIG. 24).
Place the mosquito net and secure with Velcros. Place the rain cover on the buggy and secure with Velcros around the
frame (FIG. 25).
VII MOUNTING THE BABY CAR SEAT The supplied adapters (L) are compatible with the following car seats: Kinderkraft,
Maxi Cosi®, Cybex® and are suitable for models such as: Kinderkraft MINK, Cybex Aton, Aton 2, Aton Q i Maxi Cosi Mico,
Mico AP, Mico NXT, Mico Max 30, Citi, Cabrio, and CabrioFix.
Slide the adapters into the slots in the frame until you hear the sound of the lock (FIG. 26). The adapters should be slightly
tilted to the parent. Put the seat in the adapters and make sure it is properly secured. XMOOV buggy with MINK car seat
are shown in Figure 27. To remove the adapters of the buggy frame, press the lock button in each of the adapters (FIG. 28).
WARNING! The seat must be always placed on the frame back
to the direction of travel (the child should face the person
pushing the buggy).
VIII USE OF BRAKE The buggy is equipped with a foot brake located on the rear axle. Press the brake pedal down to
activate it. The brake is released after the pedal is lifted up (FIG. 29).
IX BUGGY DISASSEMBLY After removing the bassinet/seat or child safety seat (FIG. 28 & 39), press the frame collapse
lock, and then pull the levers at both sides and finish with pushing down the parent handle (FIG. 30). A correctly folded
frame must be secured with the side lock (FIG. 31). If necessary, the front and rear wheels can be removed from the
frame by pressing the buttons marked in Figures 32 and 33.
X BUGGY ADJUSTMENT Front wheels in the MOOV buggy can be blocked in the forward movement position. Enable this
mode by lowering the lock sliders (FIG. 34). To unlock the front wheels, pull the sliders up.
The hood can be enlarged by opening the zip fastener on the outer side of the cover (FIG. 35).
To adjust the parent handle, press the lock buttons on both sides of the buggy and adjust the handle to a comfortable
height (FIG. 36).
The safety bar can be detached from the frame partially or completely by pressing a button on the side/sides (FIG. 37)
The seat tilt angle can be adjusted using the lever at the top (FIG. 38). The seat has three positions: lying, reclining and
sitting.
WARNING! When the seat is in the reclining position, do not unfasten
the straps at the back of the backrest, as this may cause the child's
head to be positioned lower than the rest of their body.
29
Advertenties
Inhoudsopgave
