Advertenties
Status
One (1) LED slow-flashes green
One (1) LED quick-flashes green
One (1) LED quick-flashes yellow
One (1) LED shows yellow
One (1) LED quick-flashes red
Indicators showing the battery's state of health
To check the battery's state of health, press the release button and hold it down for longer than three seconds. The system does not detect a
potential malfunction of the battery due to misuse, for example battery dropped or pierced, external heat damage, etc.
Status
All LEDs show in sequence, followed by one (1) LED showing con-
stantly green.
All LEDs show in sequence, followed by one (1) LED quick-flashing
yellow.
All LEDs show in sequence, followed by one (1) LED showing con-
stantly red.
Items supplied
Crimping tool, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group
Technical data
Product generation
Rated voltage
Weight in accordance with EPTA Procedure 01
Max. crimping / pressing force
Crimping / pressing time
Max. permissible crimping capacity
Storage temperature
Ambient temperature for operation
Noise information and vibration values in accordance with EN 62841
The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to
compare one power tool with another. They can also be used for a preliminary assessment of exposure.
The data given represent the main applications of the power tool. However, if the power tool is used for different applications, with different
accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period.
An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually
being used for a job. This can significantly reduce exposure over the total working period.
Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: maintaining the power tool
and accessory tools, keeping the hands warm, organization of work patterns.
Noise values
Sound power level (L
)
WA
Uncertainty for the sound power level (K
*2321724*
Cu standard strand
Cu fine strand
Al
)
WA
2321724
Meaning
State of charge: < 10 %
The Li-ion battery is completely discharged. Recharge the battery.
If the LED again starts quick-flashing after the battery has been
charged, consult Hilti Service.
The Li-ion battery or the product in which it is inserted is overload-
ed, too hot or too cold, or experiencing some other fault.
Bring the product and the battery to the recommended working
temperature and do not overload the product when it is in use.
If the message persists, consult Hilti Service.
The Li-ion battery and the product in which it is inserted are not
compatible. Consult Hilti Service.
The Li-ion battery is locked and cannot be used. Consult Hilti Ser-
vice.
Meaning
The battery can remain in use.
The check to ascertain the battery's state of health did not com-
plete. Repeat the procedure, or consult Hilti Service.
If a connected product can still be used, the remaining battery ca-
pacity is below 50 %.
If a connected product can no longer be used, the battery has
reached the end of its useful life and has to be replaced. Consult
Hilti Service.
NCR 60 DC-22
02
21.6 V
2.4 kg
30 kN ... 60 kN
≈ 5 s
240 mm²
240 mm²
240 mm²
−20 ℃ ... 70 ℃
−17 ℃ ... 60 ℃
NCR 60 D-22
02
21.6 V
2.4 kg
30 kN ... 60 kN
≈ 5 s
240 mm²
240 mm²
240 mm²
−20 ℃ ... 70 ℃
−17 ℃ ... 60 ℃
77 dB(A)
2.5 dB(A)
15
Advertenties
