Advertenties
▶
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service
providers.
Additional safety instructions, crimping tool
Safety when working in the vicinity of electrical installations
Invariably, before work commences a risk assessment has to be carried out, and the necessary protective measures have to be implemented.
All personnel involved in work in the vicinity of electrical installations must have received instruction concerning the applicable safety
requirements, safety regulations and company operating procedures.
Working procedures are divided into three different procedures: dead working, live working, working in the vicinity of live parts. All these
procedures are based on the use of protective measures against electric shock and/or the effects of short-circuits and arcing. For further
details refer to EN 50110 and any national requirements and practices. It shall be verified that all methods and tools chosen are suitable for the
installation to be worked on.
▶
For all work on electrical installations, observe the valid international, national and local laws and regulations, such as EN 50110.
Personal safety
▶
Comply with the country-specific standards and safety instructions for operation of crimping tools and all work on, with or in proximity to
electrically live equipment and lines.
▶
Persons who work in the vicinity of live lines must receive regular instruction and training.
▶
Use the product and accessories only when they are in perfect working order.
▶
Never tamper with or modify the product or accessories in any way.
▶
Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents.
▶
If you notice oil escaping, cease working with the tool and consult Hilti Service. Immediately remove the leaked oil.
▶
Check that the locking pin is pushed in all the way and securely engaged.
▶
Throughout the crimping operation, take great care to keep your hands and fingers well clear of the crimping head.
▶
Switch the crimping tool on only after bringing it to the working position.
▶
Wait until the product has come to a complete stop before you lay it down.
▶
Be extra-careful when working on lines that are under mechanical tension.
▶
Always hold the crimping tool firmly with both hands on the grips provided for the purpose.
▶
Before each use, inspect the red coating on the crimping head for indications of damage or aging. If you find such damage, the black housing
is visible and/or the crush-hazard or electric-shock hazard symbol is no longer legible, do not use the crimping tool and contact Hilti Service.
▶
Do not secure a belt hook to this power tool.
▶
Risk of injury by falling tools and/or accessories. Before starting work, check that installed accessories are secure.
▶
Do not look directly into the light source (LED) of the product and do not aim the beam at other persons' faces. Risk of dazzling or eye
damage.
▶
Keep the retaining strap and the tether clean and dry.
Electrical safety
▶
Before use of the crimping tool, all live cables and other equipment carrying electric voltage within the area in which the user is working are to
be switched off. If this is not possible, the corresponding safety precautions for working in proximity to electrically live cables or equipment
applicable in your country must be implemented and observed.
▶
Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the product
could give you an electric shock or cause an explosion if you accidentally damage an electric cable or a gas or water pipe.
▶
Do not crimp live parts, i.e. parts carrying electric voltage. The crimping tool must be considered as being uninsulated and must therefore be
used in combination with personal protective equipment (protective gloves, protective footwear, protective clothing, etc.) of a type suitable
to provide protection for yourself and other persons in the vicinity. It is essential to ensure adequate insulation for working in the vicinity
of electrically live lines, for example by the use of solid insulating material or maintenance of an adequate air gap. Among other uses, the
crimping tool is suitable for use on electrically insulating aerial lifts or platforms.
▶
In order to use the crimping tool in the vicinity of electrically live lines, the user must:
▶
take all different potentials (voltages) into account.
▶
make sure that all chosen measures and tools are appropriate for the application.
▶
be trained for working on electrically live lines.
▶
wear fit-for-purpose personal protective equipment.
▶
wear appropriate, close-fitting clothing.
▶
remove metallic lifestyle accessories such as jewelry.
Power tool use and care
▶
After approx. 50 consecutive crimping operations, switch the power tool off and allow it to cool down for about 15 minutes. Overheating can
lead to damage to the crimping tool.
▶
Store the crimping tool in a dry place inaccessible to children and unauthorized persons.
▶
Hilti recommends having the crimping tool overhauled by Hilti Service after 15,000 crimping operations.
Careful handling and use of batteries
▶
Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin
irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶
Use only batteries that are in perfect working order.
▶
Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
▶
Do not under any circumstances modify or tamper with batteries!
▶
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
▶
Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of
damage.
*2321724*
2321724
13
Advertenties
