Advertenties
▶
Never use recycled or repaired batteries.
▶
Never use the battery or a battery-operated power tool as a striking tool.
▶
Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
▶
Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and
also cause material damage and personal injury.
▶
Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
▶
Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
▶
Do not use or store the battery in explosive environments.
▶
If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire,
at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is
faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these
operating instructions.
Description
1
Product overview
Crimping head
@
Piston return switch
;
Servicing and fault indicator
=
Battery release button
%
Battery status indicator
&
Battery
(
Intended use
The product described is a cordless, electro-hydraulic crimping tool.
It is designed for crimping connection material made of copper (Cu) or aluminum (Al).
Before work commences, all live cables and other equipment carrying electric voltage within the area in which the user is working must
be switched off. If this is not possible, the corresponding safety precautions for working in proximity to live cables or equipment must be
implemented and observed.
• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries
stated in the table at the end of these operating instructions for this product.
• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.
Possible misuse
• Do not use this hand-held crimping tool clamped in a fixed position or as a stationary device.
• Do not use the electro-hydraulic crimping tool in heavy rain or under water.
Coated crimping head
NCR 60 DC-22
DANGER
Electricity presents a risk of fatal accident! Contact with electrically live lines can lead to severe physical injury and/or death.
▶
The crimping tool is not insulated! If you use this crimping tool in the vicinity of electrically live lines, wear personal protective equipment.
The crimping head of the NCR 60DC-22 has a PVC coating. The PVC coating is red, the housing underneath is colored black.
Before each use, inspect the red coating on the crimping head for indications of damage or aging. If you find such damage, the black
surface of the housing is visible and/or the crush-hazard or electric-shock hazard symbol is no longer legible, do not use the crimping
tool and contact Hilti Service.
Status indicators of the Liion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.
Indicators for state of charge and fault messages
WARNING
Risk of injury by a falling battery!
▶
If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following status indications is applicable at the time.
State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.
Status
Four (4) LEDs show constantly green
Three (3) LEDs show constantly green
Two (2) LEDs show constantly green
One (1) LED shows constantly green
14
Installation opening for accessories
)
Work-area light
+
Control switch
§
Crimping/pressing ram
/
Pivoting bar
:
Tab
∙
Meaning
State of charge: 100 % to 71 %
State of charge: 70 % to 51 %
State of charge: 50 % to 26 %
State of charge: 25 % to 10 %
2321724
18
*2321724*
Advertenties
