Inhoudsopgave
Advertenties
suitable for washing cars, car trailers, buildings, boats, ceramic tiles,
etc. Appropriate accessories allow you to mix cleaning agents. The
device is placed on an ergonomic trolley with handles for
accessories and a reel for high-pressure hose.
Do not use the device contrary to its intended use.
DESCRIPTION OF THE GRAPHIC SIDES
The numbering below refers to the device components shown on
the graphic pages of this manual.
1. High-pressure hose drum
2. Hanger for the power cord
3. Switch
4. Detergent dosing regulator
5. Grip foot of the gun
6. Gun holder
7. High pressure hose connection
8. Auxiliary handles for accessories
9. Quick coupler with built-in filter
10. Detergent container
11. Quick-disconnect gun pressure hose connection
12. Gun lock
13. High pressure hose
14. Foaming switch
* There may be differences between the drawing and the product.
EQUIPMENT AND ACCESSORIES
1. Pistol (folding lance) - 1 pc.
2. Quick coupler with filter - 1 pc.
3. Pistol holder - 1 pc.
4. Pistol holder foot - 1 pc.
5. Cable holder - 1 pc.
6. Screws - 2 pcs.
7. Nozzle pin - 1 pc.
8. User manual - 1 pc.
PREPARATION TO WORK
PREPARATION TO WORK
• Screw the quick coupling with the built-in filter (9) onto the water
inlet.
• Install the power cord hanger (2) and the gun holder (6) by
inserting them into the device guides from above.
• Fasten the foot of the gun handle (5) with two screws.
• Connect the gun (lance) by twisting it (15) and connect it by
inserting the high pressure hose (13) into the quick coupling of the
gun pressure hose (11) until it locks.
ADJUSTMENT OF PRESSURE AND STREAM RATE
The nozzle (14) enables smooth regulation of the size of the stream
from point to wide through its rotational movement (tightening /
unscrewing). The nozzle (14) also enables and disables the foaming
function. To turn on the foaming function pull out the nozzle (14),
to turn it off push the nozzle towards the gun handle.
The spot stream should be used for washing small, heavily soiled
surfaces. The wide jet is used to wash large, lightly soiled surfaces.
OPERATION / SETTINGS
ON / OFF
The mains voltage must correspond to the voltage specified on the
washer's rating plate.
Before using the pressure washer, make sure that there are no other
people or pets in the workplace.
It is not allowed to use the washer without first unwinding the high
pressure hose from the drum. Do not kink the high pressure hose.
When using the washer, it is recommended to hold the pistol grip
with one hand and the lance with the other hand. Holding it with
both hands protects against uncontrolled kickback of the lance at
the time of starting and working.
Before operating, the trigger of the pistol grip should be pulled in
to purge air from the pump and high pressure hose.
Turning on
• Make sure the pressure washer is properly assembled and ready
for use.
• Connect the water supply to the quick coupler (9).
• Unwind the high pressure hose from the drum (1).
• Check that the switch (3) is in the off position "0FF / 0"
• Open the water tap fully. Check the tightness of the connections.
• Unlock the pistol grip trigger with the trigger lock switch (12).
• Press the trigger of the gun fully until the water flow is even and
there is no air in the device and high pressure hose
• Release the gun trigger and lock it with the trigger lock lever (12).
• Connect the plug of the power cord to the mains socket.
• Turn on the device by setting the switch (3) to the "ON / I" position.
Note! Before turning on the washer, always make sure that
water flows through the device, which means that there is no
air in it.
• Release the trigger lock lever (12) and point the nozzle outlet onto
the test surface.
• Adjust the water flow. Perform the final wash.
• To temporarily turn off, release the pressure on the trigger, the
device will enter Stand-by mode.
• As soon as the trigger switch is pressed again, the high pressure
washer will reactivate.
Attention! Whenever you put the gun down or not use it, lock
the gun with the lock switch (12).
Exclusion
• Release pressure on trigger. Secure with trigger lock lever (12). The
drain is blocked and the washer cannot be accidentally started.
• Turn off the device by setting the switch (3) to the "0FF / 0"
position.
• Turn off the water supply.
• Disconnect the device from the power socket.
• Disengage the trigger lock (12), and squeeze the trigger fully until
there is no more pressurized water in the unit.
• Release trigger and re-lock trigger lock (12).
• Disconnect the connection hose from the device and the water
connection.
• After the washer is turned off, the pressure remains inside. Even
after the washer is turned off, the water jet must not be directed at
people, animals, electrical equipment and the device itself.
• Ambient temperature during operation with the washer should be
between 5˚C and 40˚C.
DETERGENT SPRAY
The washer is designed for use with cleaning agents intended for
this type of device. The use of other cleaning agents may adversely
affect the safety of the appliance. Do not use acids, gasoline,
kerosene or other flammable liquids as a cleaning agent. Only
household detergents (pH 6 ÷ 8) can be used.
Some surfaces may be damaged by the high-pressure jets of water.
Make sure the pistol grip trigger is locked (12).
• Remove the cap and fill the detergent tank (10) with a properly
prepared detergent, according to the instructions on the detergent
package.
• Pull out the nozzle (14) to set the foaming mode.
• Aim the nozzle at the surface to be coated with detergent and
release the trigger lock.
10
Advertenties
Inhoudsopgave
