Download Inhoudsopgave Inhoud Print deze pagina
Inhoudsopgave

Advertenties

All manuals and user guides at all-guides.com
TEC Thermal Printer
B-480-QP SERIES
Owner's Manual
Mode d'emploi
Bedienungsanleitung
Manual de instrucciones
Gebruikershandleiding
Manuale Utente

Advertenties

Inhoudsopgave
loading

Samenvatting van Inhoud voor Toshiba B-480-QP Series

  • Pagina 1 All manuals and user guides at all-guides.com TEC Thermal Printer B-480-QP SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente...
  • Pagina 2: List Of Standards Of Conformity

    The product herewith complies with the requirements of the Low Voltage Directive 73/23/ EEC, and the EMC directive 89/336/EEC. The product was tested in a typical set up TOSHIBA TEC personnel advocated. The following technical documentation has been filed for review.
  • Pagina 3 All manuals and user guides at all-guides.com TEC Thermal Printer B-480-QP SERIES Owner’s Manual...
  • Pagina 4: Meanings Of Each Symbol

    Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off the power, unplug the machine, then contact your authorized TOSHIBA TEC representative for assistance. Meanings of Each Symbol This symbol indicates warning items (including cautions).
  • Pagina 5 Request Regarding Maintenance • Utilize our maintenance services. After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.
  • Pagina 6: Inhoudsopgave

    CAUTION: 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. 3. Please refer to your local Authorized Service representative with regard to any queries...
  • Pagina 7: Introduction

    All manuals and user guides at all-guides.com 1. INTRODUCTION ENGLISH VERSION EO1-33007 1. INTRODUCTION 1. INTRODUCTION Thank you for choosing the TEC B-480 series thermal/transfer printer. This high performance printer is equipped with superior hardware including the specially developed (12 dots/mm, 304.8 dots/inch) near edge print head which will allow very clear print at a maximum speed of 203.2 mm/sec.
  • Pagina 8: Applicable Model

    All manuals and user guides at all-guides.com 1. INTRODUCTION ENGLISH VERSION EO1-33007 1.1 Applicable Model 1.1 Applicable Model • B-482-TS10-QP Model name description B - 4 8 2 - T S 1 0 - Q P QP: European version Issue mode S: Batch Resolution T: 12 dots/mm...
  • Pagina 9: Specifications

    All manuals and user guides at all-guides.com 2. SPECIFICATIONS ENGLISH VERSION EO1-33007 2.1 Printer 2. SPECIFICATIONS 2.1 Printer Model B-480-TS10-QP Item Supply voltage AC 220V ~ 240V +10%, -15%, 50Hz Power consumption 1.13A, 128W maximum (standby: 250mA, 23W) Operating temperature range 5 C ~ 40 C (41 F ~ 104 F) Relative humidity 25% ~ 85%RH (no condensation)
  • Pagina 10: Ribbon

    Width 2. To ensure print quality and print head life use only Length 600 m TOSHIBA TEC specified media and ribbons. Outer diameter ø90 mm (max.) 3. When using the cutter ensure that label length B plus inter label gap length E exceeds 35 mm. (i.e. label pitch should be greater that 35 mm.) (See Page 2-3.)
  • Pagina 11: Media

    All manuals and user guides at all-guides.com 2. SPECIFICATIONS ENGLISH VERSION EO1-33007 2.4 Media Tag paper Label Refer to the following 2.4 Media NOTE 2. Black Mark Black Mark (on reverse side) (on reverse side) Stop Stop Tag paper position position position position...
  • Pagina 12: Overview

    All manuals and user guides at all-guides.com 3. OVERVIEW ENGLISH VERSION EO1-33007 3.1 Front/Rear View 3. OVERVIEW 3.1 Front/Rear View Front View Rear View Top Cover Message Display (LCD) Supply Window PCMCIA Card Slot (2 slots) Serial Interface Connector (RS-232C) Operation Panel Expansion I/O Parallel I/F Connector...
  • Pagina 13: Installing The Printer

    All manuals and user guides at all-guides.com 4. INSTALLING THE PRINTER ENGLISH VERSION EO1-33007 4.1 Connecting the Power Cord and Cables 4. INSTALLING THE PRINTER 4.1 Connecting the Power Cord and Cables WARNING: Turn the POWER SWITCH to OFF before connecting the power cord or cables. Serial I/F Cable (RS-232C) Parallel I/F Cable (Centronics) Expansion I/O Cable (Option)
  • Pagina 14: Loading The Media

    All manuals and user guides at all-guides.com 5. LOADING THE MEDIA ENGLISH VERSION EO1-33007 5. LOADING THE MEDIA 5. LOADING THE MEDIA WARNING: 1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, push the switch in the “OFF”...
  • Pagina 15 NOTE: When using the label rolled with labels facing outside, please remove the upper plates of both paper holders using the following procedure. Failure to do this may cause a paper jam error. If you have any questions, please contact your nearest TOSHIBA TEC service representative. E5-2...
  • Pagina 16: Removing The Paper Holders' Upper Plates From The Media Guide

    All manuals and user guides at all-guides.com 5. LOADING THE MEDIA ENGLISH VERSION EO1-33007 5. LOADING THE MEDIA Removing the paper holders' upper plates from the media guide 1 Remove the two T-4x8 screws to detach the media guide from the printer. Media Guide Screw (T-4x8) Fig.
  • Pagina 17: Setting The Feed Gap Sensor Position

    All manuals and user guides at all-guides.com 5. LOADING THE MEDIA ENGLISH VERSION EO1-33007 5. LOADING THE MEDIA An easy way to set the black mark sensor position 1 Pull the media about 500 mm out of the front of the printer, turn the media back on it's self and feed it under the print head past the sensor so that the black mark can be seen from above.
  • Pagina 18 All manuals and user guides at all-guides.com 5. LOADING THE MEDIA ENGLISH VERSION EO1-33007 5. LOADING THE MEDIA 10. The media is now loaded and the sensor position is set. Batch type: Media Fig. 5-9 NOTE: Set the selection switch to the STANDARD/STRIP position. Improper setting can affect the print quality.
  • Pagina 19 NOTES: 1. Be sure to cut the backing paper of label. Cutting labels will cause the glue to stick to the cutter, which may affect the cutter quality and shorten the life. 2. If a label winds onto the platen during cut issue, please contact your nearest TOSHIBA TEC service representative.
  • Pagina 20: Loading The Ribbon

    All manuals and user guides at all-guides.com 6. LOADING THE RIBBON ENGLISH VERSION EO1-33007 6. LOADING THE RIBBON 6. LOADING THE RIBBON WARNING: 1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, push the switch in the “OFF”...
  • Pagina 21: Inserting The Optional Pcmcia Card

    All manuals and user guides at all-guides.com 7. INSERTING THE OPTIONAL PCMCIA CARD ENGLISH VERSION EO1-33007 7. INSERTING THE OPTIONAL PCMCIA CARD 7. INSERTING THE OPTIONAL PCMCIA CARD WARNING: Turn the power OFF when inserting or removing the PCMCIA card. CAUTION: To protect PCMCIA cards, discharge static electricity from your body by touching the printer rear cover prior touching the PCMCIA cards.
  • Pagina 22: Care/Handling Of The Media And Ribbon

    All manuals and user guides at all-guides.com 8. CARE/HANDLING OF THE MEDIA AND RIBBON ENGLISH VERSION EO1-33007 8. CARE/HANDLING OF THE MEDIA AND RIBBON 8. CARE/HANDLING OF THE MEDIA AND RIBBON CAUTION: Be sure to read carefully and understand the Supply Manual. Use only media and ribbon which meet specified requirements.
  • Pagina 23: General Maintenance

    All manuals and user guides at all-guides.com 9. GENERAL MAINTENANCE ENGLISH VERSION EO1-33007 9.1 Cleaning 9. GENERAL MAINTENANCE WARNING: 1. Be careful when handling the print head as it becomes very hot. 2. Care must be taken not to injure yourself with the printer paper cutter. 3.
  • Pagina 24: Covers And Panels

    All manuals and user guides at all-guides.com 9. GENERAL MAINTENANCE ENGLISH VERSION EO1-33007 9.2 Covers and Panels 9.2 Covers and Panels The covers should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution.
  • Pagina 25: Cleaning The Cutter Unit

    All manuals and user guides at all-guides.com 9. GENERAL MAINTENANCE ENGLISH VERSION EO1-33007 9.3 Removing Jammed Paper Cleaning the Cutter Unit WARNING: 1. Be sure to turn the power off before cleaning the cutter unit. 2. The cutters are sharp and care should be taken not to injure yourself when cleaning. The swing cutter and rotary cutter are available as an option.
  • Pagina 26: Threshold Setting

    All manuals and user guides at all-guides.com 9. GENERAL MAINTENANCE ENGLISH VERSION EO1-33007 9.4 Threshold Setting 9.4 Threshold Setting For the printer to maintain a constant print position it uses the feed gap sensor to detect the gap between labels by measuring the amount of light passing through the media. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jammed errors.
  • Pagina 27: Auto Ribbon Saving Mode

    Auto Ribbon Saving Mode Auto ribbon saving function is activated when a no print area extends more than 17 mm. For further information on this function, please ask your nearest TOSHIBA TEC service representative. NOTE: According to the relation between the outer diameter of rewound ribbon and print speed, ribbon...
  • Pagina 28: Troubleshooting

    All manuals and user guides at all-guides.com 10. TROUBLESHOOTING ENGLISH VERSION EO1-33007 10. TROUBLESHOOTING 10. TROUBLESHOOTING WARNING: If you cannot solve a problem with the following solutions, do not attempt to repair it yourself. Turn the power off, unplug the printer, then contact your Authorized Service representative for assis- tance.
  • Pagina 29 All manuals and user guides at all-guides.com 10. TROUBLESHOOTING ENGLISH VERSION EO1-33007 10. TROUBLESHOOTING Error Message Problem Solution CUTTER ERROR Media is jammed in the cutter. Remove the jammed media and feed **** the undamaged media through the cutter. Press the [RESTART] key. Else Turn the power off and contact your Authorized Service representative.
  • Pagina 30 All manuals and user guides at all-guides.com 10. TROUBLESHOOTING ENGLISH VERSION EO1-33007 10. TROUBLESHOOTING Problem Solution No print. 1. Check that media and the ribbon is loaded correctly. 2. Check whether the print head is set correctly or not. 3. Check the cabling between the printer and the host. Dots missing in the print.
  • Pagina 31 All manuals and user guides at all-guides.com I'imprimante Transfert Thermique TEC B-480-QP SERIES Mode d’emploi...
  • Pagina 32: Résumé Des Précautions

    Ne tentez pas díeffectuer des réparations ou des modifications sur ce matériel. Si une erreur se produit qui ne peut être résolue en suivant les instructions de ce manuel, coupez le courant, déconnectez le câble secteur et contactez votre revendeur agréé TOSHIBA TEC pour une assistance technique. Explication des symboles Ce symbole signale une mise en garde (ou des précautions).
  • Pagina 33 Au sujet de la maintenance • Faites appel à nos services de maintenance. Aprés avoir reçu le matériel, prenez contact avec votre revendeur agréé TOSHIBA TEC pour une visite de maintenance annuelle, de manière à effectuer un nettoyage complet de líintérieur de la machine.
  • Pagina 34 1. Ce manuel ne peut être copié, en entier ni en partie sams autorisation préalable de TOSHIBA TEC. 2. Le contenu de ce manuel peut être changé sans information préalable. 3. Veuillez contacter votre distributeur TOSHIBA TEC pour toutes questions.
  • Pagina 35: Introduction

    All manuals and user guides at all-guides.com 1. INTRODUCTION FRENCH VERSION FO1-33007 1. INTRODUCTION 1. INTRODUCTION Nous vous remercions d'avoir porté votre choix sur l'imprimante transfert thermique de la série B-480. Cette nouvelle génération d'imprimante intègre le meilleur compromis performance qualité. La tête thermique est à...
  • Pagina 36: Modèle Applicable

    All manuals and user guides at all-guides.com 1. INTRODUCTION FRENCH VERSION FO1-33007 1.1 Modèle Applicable 1.1 Modèle Applicable • B-482-TS10-QP Description du modèle B - 4 8 2 - T S 1 0 - Q P QP: Version pour l'Europe Mode d'impression S: Par Série Résolution...
  • Pagina 37: Specifications

    All manuals and user guides at all-guides.com 2. SPECIFICATIONS FRENCH VERSION FO1-33007 2.1 Imprimante 2. SPECIFICATIONS 2.1 Imprimante Type B-480-TS10-QP Article Alimentation CA 220 ~ 240 V + 10 %, -15 %, 50 Hz Consommation 1.13A, 128W max. (attente: 250 mA, 23 W) Limites de température 5 C ~ 40 C Humidité...
  • Pagina 38: Options

    étiquettes. 600 m Longueur 2. Il est recommandé d'utiliser des rubans et des papiers recommandés par TOSHIBA TEC. ø90 mm (max.) Diamètre externe 3. La coupe des étiquettes adhésives peut se faire à partir d'une hauteur de 35 mm.
  • Pagina 39: Papier

    All manuals and user guides at all-guides.com 2. SPECIFICATIONS FRENCH VERSION FO1-33007 2.4 Papier Reportez-vous la 2.4 Papier NOTE 2 ci-dessous. Etiquette carton Etiquette Marque noir Position (au dos) Marque noir d but (au dos) Position d but d’impression d’impression Etiquette carton Position Position...
  • Pagina 40: Vue Generale

    All manuals and user guides at all-guides.com 3. VUE GENERALE FRENCH VERSION FO1-33007 3.1 Face Avant et Arrière 3. VUE GENERALE 3.1 Face Avant et Arrière Vue de face Vue de la face arrière Capot Afficheur (LCD) Vue des consommables Emplacements pour carte PCMCIA (2 ports) Connecteur...
  • Pagina 41: Mise En Route De L'impreimante

    All manuals and user guides at all-guides.com 4. MISE EN ROUTE DE L'IMPRIMANTE FRENCH VERSION FO1-33007 4.1 Connexion du cordon d'alimentation et des câbles 4. MISE EN ROUTE DE L'IMPRIMANTE 4.1 Connexion du cordon d'alimentation et des câbles AVERTISSEMENT: Prendre soin de couper l'alimentation avant de connecter le cordon d'alimentation et les autres câbles.
  • Pagina 42: Chargement Du Papier

    All manuals and user guides at all-guides.com 5. CHARGEMENT DU PAPIER FRENCH VERSION FO1-33007 5. CHARGEMENT DU PAPIER 5. CHARGEMENT DU PAPIER AVERTISSEMENT: 1. Ne pas toucher des parties mobiles. Pour réduire le risque que deses doigts, la joaillerie, les vétements, etc., seraient tirer dans les parties mobiles, pousser l’interrupteur à...
  • Pagina 43 NOTE: Lors de l'utilisation de rouleaux d'étiquettes avec enroulement extérieur, veuillez enlever les deux plaques porte-papier en suivant la procédure suivante. Laisser les plaques pent provoquer des bourrages papier. N'hésitez pas à contacter votre agence TOSHIBA TEC la plus proche pour tous renseignements. F5-2...
  • Pagina 44 All manuals and user guides at all-guides.com 5. CHARGEMENT DU PAPIER FRENCH VERSION FO1-33007 5. CHARGEMENT DU PAPIER Démontage des plaques porte papier du guide papier 1 Retirez les deux vis T-4x8 pour séparer le guide papier de l'imprimante. Guide papier Vis (T-4x8) Fig.
  • Pagina 45: Positionnement De La Cellule De Marque Noire

    All manuals and user guides at all-guides.com 5. CHARGEMENT DU PAPIER FRENCH VERSION FO1-33007 5. CHARGEMENT DU PAPIER Positionnement de la cellule de marque noire 1 Sortir le papier de 500 mm et le faire entrer de nouveau sous la tête jusqu'aux cellules. 2 Ajuster la position de la cellule marque noire pour avoir votre marque au milieu de celle-ci.
  • Pagina 46 All manuals and user guides at all-guides.com 5. CHARGEMENT DU PAPIER FRENCH VERSION FO1-33007 5. CHARGEMENT DU PAPIER 10. Les opérations de chargement du papier et du réglage des cellules sont terminées. Impression par lot: Papier Fig. 5-9 NOTE: Placer le DIP SWITCH en position de STANDARD/STRIP. Une mauvaise position peut affecter la qualité...
  • Pagina 47 Dans ce cas, coupez dans l'échenillage. 2. Si le bord des étiquettes s'enroule sur le rouleau d'impression en mode massicot, prenez contact avec votre centre de maintenance TOSHIBA TEC. 3. Pour sélectionner l'option cutter, le DIP SWITCH peut être placé sur l'autre position.
  • Pagina 48: Chargement Du Film

    All manuals and user guides at all-guides.com 6. CHARGEMENT DU FILM FRENCH VERSION FO1-33007 6. CHARGEMENT DU FILM 6. CHARGEMENT DU FILM AVERTISSEMENT: 1. Ne pas toucher des parties mobiles. Pour réduire le risque que deses doigts, la joaillerie, les vétements, etc., seraient tirer dans les parties mobiles, pousser l’interrupteur à...
  • Pagina 49: Installation De La Carte Pcmcia Optionnelle

    All manuals and user guides at all-guides.com 7. INSTALLATION DE LA CARTE PCMCIA OPTIONNELLE FRENCH VERSION FO1-33007 7. INSTALLATION DE LA CARTE PCMCIA OPTIONNELLE 7. INSTALLATION DE LA CARTE PCMCIA OPTIONNELLE ATTENTION: Mettez l'imprimante hors tension avant d'enficher ou de retirer une carte PCMCIA. PRECAUTION: Pour protéger les cartes PCMCIA, déchargez votre électricité...
  • Pagina 50: Precaution De Stockage Des Consommables

    8. PRECAUTIONS DE STOCKAGE DES CONSOMMABLES 8. PRECAUTIONS DE STOCKAGE DES CONSOMMABLES Utiliser uniquement des fournitures aux recommandations TOSHIBA TEC. La raison de ces spécifications est d'assurer une bonne qualité d'impression, durée de vie de la tête et de produire des codes à barre lisibles. L'utilisation de fournitures hors normes peut réduire la durée de vie de la tête et provoquer de mauvaises impressions.
  • Pagina 51: Maintenance

    All manuals and user guides at all-guides.com 9. MAINTENANCE FRENCH VERSION FO1-33007 9.1 Nettoyage 9. MAINTENANCE ATTENTION: 1. Attention, lorsque vous ouvrez le bloc d’impression, celui-ci peut étre chaud. 2. Faire attention au couteau de l’imprimante. 3. Ne pas toucher des parties mobiles. Pour réduire le risque que deses doigts, la joaillerie, les vétements, etc., seraient tirer dans les parties mobiles, pousser l’interrupteur à...
  • Pagina 52: Capot, Face Avant

    Fig. 9-2 9. Le bourrage dans le couteau peut être provoqué par l'usure de la lame. Ne pas utiliser de papier en dehors des spécifications. Si le bourrage se produit trop souvent, contacter votre service après vente TOSHIBA TEC. F9-2...
  • Pagina 53 All manuals and user guides at all-guides.com 9. MAINTENANCE FRENCH VERSION FO1-33007 9.3 Elimination des Fournitures Coincées Nettoyage du couteau ATTENTION: 1. Vérifier que l'imprimante est hors tension. 2. Veiller à ne pas abîmer la lame du couteau. Les massicots, rotatif ou à baïonnette, sont disponibles en option. Ils se nettoient de la même manière malgré...
  • Pagina 54: Régler La Détection Des Étiquettes Pré-Imprimées

    All manuals and user guides at all-guides.com 9. MAINTENANCE FRENCH VERSION FO1-33007 9.4 Régler la Détection des Etiquettes Pré-imprimées 9.4 Régler la Détection des Etiquettes Pré-imprimées Pour imprimer les étiquettes à une position constante, une cellule de transparence est utilisée pour détecter l'échenillage entre deux étiquettes ceci de façon automatique.
  • Pagina 55: Economiseur De Ruban Automatique

    9.4 Régler la Détection des Etiquettes Pré-imprimées Economiseur de ruban automatique L'économiseur de film se déclenche automatiquement lorsque se présente une zone non imprimée supérieure à 17 mm. Interrogez votre centre de maintenance TOSHIBA TEC pour de plus amples renseignements à ce sujet. NOTE: En fonction de la vitesse et des diamètres des mandrins ruban, le gain de ruban est réduit de:...
  • Pagina 56: Depistage Des Pannes

    Ces messages apparaissent sur l'afficheur du panneau de contrôle. Mettre l'imprimante hors tension et contacter votre service après vente TOSHIBA TEC. Message Problème...
  • Pagina 57 ERR. transmission série (RS-232C). à nouveau ou appuyer sur la touche COMMUNICAT. [RESTART]. Contacter votre service après vente TOSHIBA TEC si nécessaire. Lors d'une erreur de syntaxe, Corriger votre application. example) l'afficheur vous indique la ligne en PC001; 0A00, cause sur 16 caractères.
  • Pagina 58 3. Vérifier si le câble d'interface est raccordé correctement. Des points n'apparaissent pas à Certains points de la tête sont défectueux. l'impression. Nettoyer la tête d'impression. Contacter votre service après vente TOSHIBA TEC si nécessaire. Impression pas nette (ou floue). 1. Tête d'impression encrassée Nettoyer la tête d'impression.
  • Pagina 59 All manuals and user guides at all-guides.com TEC Thermo-/Thermotransfer-Drucker B-480-QP SERIES Bedienungsanleitung...
  • Pagina 60 Versuchen Sie nicht selber den Drucker zu reparieren oder zu modifizieren. Wenn ein Fehler aufuritt und dieser nicht durch die in diesem Handbuch beschriebenen Maßnahmen behoben werden kann, schalten Sie das Gerät aus, ziehen Sie den Stecker und verständigen Sie lhren TOSHIBA TEC Vertragshändler. Bedeutung der Symbole Dieses Symbol weist auf Gefahren hin (einschließlich Warnungen).
  • Pagina 61 Verwenden Sie niemals Verdünner oder andere chemische Lösungsmittel zur Reinigung der Plastikteile. • Verwenden Sie nur TOSHIBA TEC Original Etikettenmaterial und Farbbänder, das den Spezifikationen von TOSHIBA TEC entspricht. • Etiketten, Etikettenmaterial und Farbbänder sollten so gelagert werden, daß sie vor direktem Sonnenlicht, hohen Termperaturen, Feuchtigkeit, Staub und Gas geschützt sind.
  • Pagina 62 2. Wir behalten uns vor, den lnhalt des Handbuches ohne Vorankündigung zu ändern. 3. Wenn Sie weitergehende Fragen haben oder Teile dieses Handbuches nicht verständlich sein sollten, wenden Sie sich bitte an Ihren TOSHIBA TEC Fachhändler oder an die zuständige TOSHIBA TEC Landesgesellschaft.
  • Pagina 63 All manuals and user guides at all-guides.com 1. EINFÜHRUNG GERMAN VERSION GO1-33007 1. EINFÜHRUNG 1. EINFÜHRUNG Vielen Dank, da Sie sich für den TEC Drucker B-480 entschieden haben. Dieser Drucker vereinigt hohe Auflösung (12 Punkte/mm ‡ 304.8 DPI) mit hoher Druckgeschwindigkeit und ist auch in industrieller Umgebung einsetzbar, da das Papier im Drucker Platz findet.
  • Pagina 64: Modellbezeichnung

    All manuals and user guides at all-guides.com 1. EINFÜHRUNG GERMAN VERSION GO1-33007 1.1 Modellbezeichnung 1.1 Modellbezeichnung • B-482-TS10-QP (Gehäuse) (Typenschild) B - 4 8 2 - T S 1 0 - Q P QP: Europa-Version Druckmodus S:kontinuierlich Auflösung T: 12 Dots/mm 2: Thermodirekt/Thermotransfer 1.2 Beipack Bediener-Handbuch...
  • Pagina 65: Spezifikationen

    All manuals and user guides at all-guides.com 2. SPEZIFIKATIONEN GERMAN VERSION GO1-33007 2.1 Drucker 2. SPEZIFIKATIONEN 2.1 Drucker B-480-TS10-QP ITEM Netzspannung AC 220V ~ 240V +10%, -15%, 50Hz Leistungssaufnahme 1.13A, 128W maximum (standby: 250mA, 23W) Temperaturbereich 5 C ~ 40 C 25% ~ 85% relative Luftfeuchte, nicht kondensierend Luftfeuchte Dünnschicht-Thermo-Druckkopf, 12 Elemente/mm, "Near Edge"...
  • Pagina 66: Optionen

    2. Um beste Druckqualität und lange Lebensdauer des Druckkopfes Länge 600 m sicherzustellen, empfehlen wir den ausschließlichen Gebrauch von Origi- nal TOSHIBA TEC Farbbändern und TOSHIBA TEC geprüften Papieren. Außendurchmes. ø90 mm (max.) 3. Im Schneidemodus bitte nur Etiketten verwenden, deren Etikettenlänge B plus einer halben Zwischenraumlänge E größer 35 mm sind.
  • Pagina 67: Papier

    All manuals and user guides at all-guides.com 2. SPEZIFIKATIONEN GERMAN VERSION GO1-33007 2.4 Papier 2.4 Papier Anhänger Etikett Siehe Hinweis 2. Reflexmarke Reflexmarke (auf Rückseite) (auf Rückseite) Stopp- Stopp- Anhänger position position Schneid- Schneid- position position Referenz- Referenz- koordinate koordinate Referenz- Referenz- koordinate...
  • Pagina 68: Überblick

    All manuals and user guides at all-guides.com 3. ÜBERBLICK GERMAN VERSION GO1-33007 3.1 Vorder- / Rückseite 3. ÜBERBLICK 3.1 Vorder- / Rückseite Vorderansicht Rückansicht Gehäusedeckel LCD Display Sichtfenster PCMCIA Kartenschacht (2 Schächte) Anschluß für serielle Schnittstelle Bedienfeld Anschluß für parallele Anschluß...
  • Pagina 69: Installation Des Druckers

    All manuals and user guides at all-guides.com 4. INSTALLATION DES DRUCKERS GERMAN VERSION GO1-33007 4.1 Anschluss der Kabel 4. INSTALLATION DES DRUCKERS 4.1 Anschluss der Kabel ACHTUNG: Den Netzschalter auf "AUS" = "0" stellen, bevor Sie Netzkabel oder andere Kabel einstecken. Serielles Kabel (RS-232C) Parallel Kabel (Centronics) Start-/Stopp-Kabel (Option)
  • Pagina 70: Einsetzen Des Papiers

    All manuals and user guides at all-guides.com 5. EINSETZEN DES PAPIERS GERMAN VERSION GO1-33007 5. EINSETZEN DES PAPIERS 5. EINSETZEN DES PAPIERS ACHTUNG: 1. Fassen Sie keine beweglichen Teile an. Um zu verhindern, daß Finger, Schmuck, Kleidungsstücke oder ähnliches von den beweglichen Teilen erfaßt werden, schalten Sie das Gerät IMMER “AUS”.
  • Pagina 71 HINWEIS: Wenn Sie Etikettenrollen mit Außenwicklung verwenden, entfernen Sie bitte die oberen Platten beider Papierhalterungen wie nachfolgend beschrieben. Falls Sie dies nicht tun, kann ein Papierstau auftreten. Sollten Sie irgendwelche Fragen haben, nehmen Sie bitte mit Ihrem TOSHIBA TEC Fachhändler Kontakt auf. G5-2...
  • Pagina 72 All manuals and user guides at all-guides.com 5. EINSETZEN DES PAPIERS GERMAN VERSION GO1-33007 5. EINSETZEN DES PAPIERS Entfernung der oberen Platten der Papierhalterung von der Papierführung 1 Entfernen Sie die zwei T-4x8 Schrauben, um die Papierführung vom Drucker zu lösen. Papierführung Schraube (T-4x8) Abb.
  • Pagina 73: Einfache Positionierung Des Reflexmarkensensors

    All manuals and user guides at all-guides.com 5. EINSETZEN DES PAPIERS GERMAN VERSION GO1-33007 5. EINSETZEN DES PAPIERS Einfache Positionierung des Reflexmarkensensors 1 Ziehen Sie das Material zunächst ca. 500 mm aus dem Drucker und führen es mit der Unterseite nach oben unter dem Kopf zurück, bis Sie eine Reflexmarke sehen können. 2 Justieren Sie nun den Reflexmarkensensor auf die Mitte der Marke (das hintere Loch zeigt die exakte Position des Sensors).
  • Pagina 74 All manuals and user guides at all-guides.com 5. EINSETZEN DES PAPIERS GERMAN VERSION GO1-33007 5. EINSETZEN DES PAPIERS 10. Das Material ist nun richtig eingesetzt und der Sensor in Position. Für kontinuierlichen Druck Papier Abb. 5-9 HINWEIS: Setzen Sie den Selektionsschalter auf STANDARD/STRIP Position. Falsches Einschalten kann die Druckqualität beeinflussen.
  • Pagina 75 Klebematerial auf dem Messer festsetzen. Dies beeinträchtigt die Qualität des Messers und verkürzt die Haltbarkeit des Messers. 2. Wickelt sich im Schneidemodus Ihr Etikettenmaterial um die Druckwalze informieren Sie bitte Ihren TOSHIBA TEC Fachhändler. 3. Für den Betrieb mit Messer kann der Selektionsschalter auf jeder Position eingestellsein. Papieraustritt...
  • Pagina 76: Einsetzen Des Farbbandes

    All manuals and user guides at all-guides.com 6. EINSETZEN DES FARBBANDES GERMAN VERSION GO1-33007 6. EINSETZEN DES FARBBANDES 6. EINSETZEN DES FARBBANDES ACHTUNG: 1. Fassen Sie keine beweglichen Teile an. Um zu verhindern, daß Finger, Schmuck, Kleidungsstücke oder ähnliches von den beweglichen Teilen erfaßt werden, schalten Sie das Gerät IMMER “AUS”.
  • Pagina 77: Einsetzen Des Zubehörs Pcmcia Karte

    All manuals and user guides at all-guides.com 7. EINSETZEN DES ZUBEHÖRS PCMCIA KARTE GERMAN VERSION EGO1-33007 7. EINSETZEN DES ZUBEHÖRS PCMCIA KARTE 7. EINSETZEN DES ZUBEHÖRS PCMCIA KARTE WARNUNG: Schalten Sie den Drucker aus bevor Sie die PCMCIA Karte einstecken oder heraus ziehen. ACHTUNG: Zum Schutz der PCMCIA Karte, entladen Sie Ihre statische Ladung durch Berühren der Röckseite des Druckers bevor Sie die PCMCIA Karte anfassen.
  • Pagina 78: Hinweise Zum Papier Und Farbband

    • Vorbedruckte Etiketten in denen Tinte benutzt wurde, können die Lebensdauer das Druckkopfes verkürzen. Benutzen Sie keine vorbedruckten Etiketten, die die Substanzen carbonic calcium (CACO und kaolin (Al , 2SiO , 2H O) enthalten. Weitere Informationen erhalten Sie von lhrem TOSHIBA TEC Händler oder lhrem Etiketten-bzw. Farbbandlieferanten. G8-1...
  • Pagina 79: Wartung

    1. Vor jeder Wartung muß das Netzkabel abgezogen werden. 2. Verwenden Sie zur Kopfreinigung niemals scharge Gegenstände wie Schraubenzieher, Nagelfeilen, etc., sondern immer nur geeignete Reiniger wie von TOSHIBA TEC beziehbar. 3. Schütten Sie niemals Wasser auf den Drucker. G9-1...
  • Pagina 80: Reinigen

    9. Ein Papierstau im Messer kann durch aufgetretenen Kleber verursacht worden sein. Verwenden Sie daher nur zugelassene Qualitäten entsprechend den TOSHIBA TEC Standards. Tritt dennoch häufiger ein Papierstau im Messer auf, so informieren Sie Ihren zuständigen TOSHIBA TEC Händler. G9-2...
  • Pagina 81: Reinigung Des Messers

    All manuals and user guides at all-guides.com 9. WARTUNG GERMAN VERSION GO1-33007 9.3 Beseitigung eines Papierstaus Reinigung des Messers ACHTUNG: 1. Der Drucker muß ausgeschaltet sein. 2. Das Messer ist sehr scharf, daher ist bei der Reinigung HÖCHSTE VORSICHT geboten, um Verletzungen zu vermeiden.
  • Pagina 82: Sensoranpassung Für Vorgedruckte Etiketten

    All manuals and user guides at all-guides.com 9. WARTUNG GERMAN VERSION GO1-33007 9.4 Sensoranpassung für vorgedruckte Etiketten 9.4 Sensoranpassung für vorgedruckte Etiketten Der Durchleuchtungssensor misst die Menge des Lichts, die durch das Papier geht, und erkennt beim Etikettenzwischenraum, daß ein neues Etikett beginnt. Hierdurch ist es möglich, von Etikett zu Etikett die Druckposition konstant zu halten.
  • Pagina 83: Automatische Farbbandoptimierung

    All manuals and user guides at all-guides.com 9. WARTUNG GERMAN VERSION GO1-33007 9.4 Sensoranpassung für vorgedruckte Etiketten Automatische Farbbandoptimierung Die automatische Farbbandoptimierung ist aktiv, wenn kein Druckbereich 17 mm überschreitet. Bei Fragen zu dieser Funktion wenden Sie sich bitte an Ihren nächsten Fachhändler. HINWEIS: Bedingt durch die Relation zwischen Außendurchmesser und der Druckgeschwindigkeit, varilert der Farbbandverlust zur Farbbandeinsparung wie in der unteren Tabelle aufgeführt.
  • Pagina 84: Fehlerbehebung

    Wenn mit den nachfolgend beschriebenen Maßnahmen ein Fehler nicht beseitigt werden kann, so schalten Sie den Drucker aus, ziehen das Netzkabel ab und nehmen Sie bitte Kontakt mit lhrem zuständigen TOSHIBA TEC-Händler auf. Versuchen Sie nicht, den Drucker selbst zu reparieren. Fehlermeldung Ursache Lösung...
  • Pagina 85 All manuals and user guides at all-guides.com 10. FEHLERBEHEBUNG GERMAN VERSION GO1-33007 10. FEHLERBEHEBUNG Error Message Problem Solution Papierstau im Messer MESSERFEHL. Gestautes Material entfernen und Mate- **** rial wieder einlegen. Taste [RESTART] drücken. Fehler beim Beschreiben der Flash FLASH FEHLER 1.
  • Pagina 86 All manuals and user guides at all-guides.com 10. FEHLERBEHEBUNG GERMAN VERSION GO1-33007 10. FEHLERBEHEBUNG Problem Lösung Kein Druck 1. Prüfen, ob Papier und Farbband richtig eingesetzt sind. 2. Prüfen, ob Druckkopf richtig verriegelt wurde. 3. Prüfen, ob Verbindung zwischen Host und Drucker richtig ist.
  • Pagina 87 All manuals and user guides at all-guides.com Impresora térmica TEC B-480-QP SERIES Manual de instrucciones...
  • Pagina 88 No intente efectuar reparaciones o modificaciones en este equipo. Si ocurriese un fallo que no se puede rectificar utilizando este manual, apague la máquina, desconecte la alimentación y contacte con su Distribuidor Autorizado TOSHIBA TEC para la asistencia técnica. Significado de cada símbolo Este símbolo indica puntos de advertencia (incluyendo precauciones).
  • Pagina 89 Compromiso de Mantenimiento • Utilice nuestros servicios de mantenimiento. Después de comprar la impresora, contacte con su Distribuidor Autorizado TOSHIBA TEC al menos una vez al año para su mantenimiento y limpieza. En caso contrario, se puede almacenar suciedad en la impresora y causar un incendio o mal funcionamiento.
  • Pagina 90 10. SOLUCION DE ERRORES............S10- 1 ATENCION: 1. Este manual no puede ser copiado total o parcialmente sin permiso escrito. 2. El contenido de este manual puede ser cambiado sin previo aviso. 3. Para cualquier consulta aclaración dirijase a su distribuidor autorizado TOSHIBA TEC.
  • Pagina 91 1. INTRODUCCION 1. INTRODUCCION Gracias por elegir la impresora térmica B-480 de TOSHIBA TEC. Esta nueva generación de impresoras de alto rendimiento y gran calidad viene equipada con lo último en hardware, incluyendo un novedoso cabezal de alta densidad (12 puntos/mm, 304.8 puntos/pulgada) con impresión por su arista que permite una impresión muy clara y una velocidad máxima de 203.2 mm/seg.
  • Pagina 92 All manuals and user guides at all-guides.com 1. INTRODUCCION SPANISH VERSION SO1-33007 1.1 Descripción del modelo 1.1 Descripción del modelo • B-482-TS10-QP Descripción del modelo B - 4 8 2 - T S 1 0 - Q P QP: Versión europea Método de emisión S: Impresión por lotes (contínua) Resolución...
  • Pagina 93 All manuals and user guides at all-guides.com 2. ESPECIFICACIONES SPANISH VERSION SO1-33007 2.1 Impresora 2. ESPECIFICACIONES 2.1 Impresora Modelo B-480-TS10-QP Características 220V ~ 240V AC +10%, -15%, 50Hz Tensión de alimentación Máximo 1.13A, 128W (parada: 250mA, 23W) Consumo 5 C ~ 40 C Rango de temperaturas 25% ~ 85%RH (sin vapor) Humedad relativa...
  • Pagina 94 Tipo de carrete tiempo. Ancho 68 mm ~ 112 mm 2. Se recomienda el uso de papel y cintas recomendadas por TOSHIBA TEC con el fin de alargar la vida del cabezal de impresión. Longitud 600 m 3. Trabajando con cortador, la etiqueta a imprimir debe cumplir que; la suma ø90 mm (max.)
  • Pagina 95 All manuals and user guides at all-guides.com 2. ESPECIFICACIONES SPANISH VERSION SO1-33007 2.4 Papel 2.4 Papel Etiqueta Cartulina Referido a la siguiente NOTA 2. Marca negra Marca negra (en cara inferior) (en cara inferior) Posición Posición Cartulina de parada de parada Posición Posición de corte...
  • Pagina 96 All manuals and user guides at all-guides.com 3. VISTA GENERAL SPANISH VERSION SO1-33007 3.1 Vista frontal y posterior de la impresora 3. VISTA GENERAL 3.1 Vista frontal y posterior de la impresora Vista frontal Vista posterior Cubierta superior Pantalla (LCD) Visor Slot para tarjeta PCMCIA (2 slots)
  • Pagina 97 All manuals and user guides at all-guides.com 4. INSTALACION DE LA IMPRESORA SPANISH VERSION SO1-33007 4.1 Conexión de los cables 4. INSTALACION DE LA IMPRESORA 4.1 Conexión de los cables ATENCIÓN: Apagar la impresora antes de conectar cualquier cable. Cable I/F serie (RS-232C) Cable I/F paralelo (Centronics) Cable de expansión I/O (opcional) Cable de...
  • Pagina 98 All manuals and user guides at all-guides.com 5. CARGA DEL PAPEL SPANISH VERSION SO1-33007 5. CARGA DEL PAPEL 5. CARGA DEL PAPEL ATENCIÓN: 1. Antes de manipular cualquier pieza de la impresora en movimiento (motors, rodillos, etc.), desenchufe la impresora de la red a fin de evitar que los dedos, joyas, ropa, etc, puedan engancharse en ellas.
  • Pagina 99 NOTA: Cuando utilice rollos con las etiquetas en la cara externa, quite las pletinas superiores de las sujeciones de papel de las siguiente forma. Un fallo al hacer esto puede causar un error de atasco de papel. Si tiene alguna duda, por favor póngase en contacto con su representante de Servicio TOSHIBA TEC más cercano. S5-2...
  • Pagina 100 All manuals and user guides at all-guides.com 5. CARGA DEL PAPEL SPANISH VERSION SO1-33007 5. CARGA DEL PAPEL Extracción de las pletinas superiores las sujeciones de la guía de papel 1 Quitar los dos tornillos T-4x8 para soltar la guía de papel de la impresora. Guía del Papel Tornillo (T-4x8) Fig.
  • Pagina 101 All manuals and user guides at all-guides.com 5. CARGA DEL PAPEL SPANISH VERSION SO1-33007 5. CARGA DEL PAPEL Ajuste de la posición del sensor de marca negra 1 Sacar unos 500 mm de papel y doblarlo de tal manera que se introduzca entre la cabeza de impresión y el papel ya introducido.
  • Pagina 102 All manuals and user guides at all-guides.com 5. CARGA DEL PAPEL SPANISH VERSION SO1-33007 5. CARGA DEL PAPEL 10. Ahora tanto el papel como la posición del sensor se encuentran ubicados correctamente. Emisión continua: Papel Fig. 5-9 NOTA: Coloque el conmutador de selección en la posición STANDARD/STRIP. Una posición incorrecta de este conmutador puede afectar a la calidad de impresión.
  • Pagina 103 2. Si el borde superior de la etiqueta entra torcido en el rodillo de impresión en emisión con corte, por favor contacte con su representante TOSHIBA TEC más cercano. 3. En el modo de emisión con core la posición del conmutador de selección no influye sobre la impresión.
  • Pagina 104 All manuals and user guides at all-guides.com 6. COLOCACION DE LA CINTA SPANISH VERSION SO1-33007 6. COLOCACION DE LA CINTA 6. COLOCACION DE LA CINTA ATENCIÓN: 1. Antes de manipular cualquier pieza de la impresora en movimiento (motors, rodillos, etc.), desenchufe la impresora de la red a fin de evitar que los dedos, joyas, ropa, etc, puedan engancharse en ellas.
  • Pagina 105 All manuals and user guides at all-guides.com 7. COMO INTRODUCIR LA TARJETA OPCIONAL PCMCIA SPANISH VERSION SO1-33007 7. COMO INTRODUCIR LA TARJETA OPCIONAL PCMCIA 7. COMO INTRODUCIR LA TARJETA OPCIONAL PCMCIA ATENCIÓN: Apagar siempre la impresora cuando se vaya a introducir o extraer la tarjeta PCMCIA. PRECAUCIÓN: Para proteger las tarjetas PCMCIA, toque la cubierta trasera de la impresora para descargarse de la electricidad estática antes de tocar la tarjeta PCMCIA.
  • Pagina 106 Por tratarse de una impresora de transferencia térmica, se aconseja que se usen las etiquetas y cintas recomendadas por TOSHIBA TEC. De lo contrario pueden resultar códigos de barras ilegibles. Trátense estas etiquetas y cintas con cuidado. En caso de usar productos en mal estado puede que los códigos impresos sean defectuosos además de acortar la vida de su cabezal.
  • Pagina 107 All manuals and user guides at all-guides.com 9. MANTENIMIENTO SPANISH VERSION SO1-33007 9.1 Limpieza 9. MANTENIMIENTO ATENCIÓN: 1. Tenga cuidado en el manejo del cabezai ya que éste puede estar caliente. 2. Tener cuidado de no cortarse con la cuchilla de la impresora. 3.
  • Pagina 108 9. Si la unidad cortadora se encuentra sucia o pegajosa, (por desprendimiento de parte del adhesivo de las etiquetas) puede producirse un atasco del papel al entrar en contacto con la unidad. Por esto se recomienda usar las etiquetas especificadas por TOSHIBA TEC. Si usted tiene frecuentemente atascos en el cortador contacte con su distribuidor autorizado.
  • Pagina 109 All manuals and user guides at all-guides.com 9. MANTENIMIENTO SPANISH VERSION SO1-33007 9.3 Cómo quitar el papel atascado Cómo limpiar la unidad cortadora ATENCIÓN: 1. Asegurarse de que la impresora se encuentra apagada antes de empezar a limpiar. 2. Tener cuidado de no cortarse con las cuchillas. El cortador de tijera y el cortador giratorio están disponibles como una opción.
  • Pagina 110 All manuals and user guides at all-guides.com 9. MANTENIMIENTO SPANISH VERSION SO1-33007 9.4 Configuración del umbral de etiqueta 9.4 Configuración del umbral de etiqueta Para empezar a imprimir etiquetas en una determinada posición, la cual va a ser fija, se usa el sensor de transparencia, el cual es usado para detectar el espacio entre etiquetas.
  • Pagina 111 Salvado automático de cinta La función de ahorro de cinta se activa cuando no se imprime en un área de más de 17 mm. Respecto a esta función, por favor contacte con su representante TOSHIBA TEC más cercano. NOTA: Debido a la relación entre el diámetro de rebobinado de la cinta ya usada y la velocidad de impresión, la cantidad de cinta perdida por cada actuación del salvado automático se ilustra en...
  • Pagina 112 All manuals and user guides at all-guides.com 10. SOLUCION DE ERRORES SPANISH VERSION SO1-33007 10. SOLUCION DE ERRORES 10. SOLUCION DE ERRORES ATENCIÓN: Se su problema no se encuentra entre los expuestos en este apartado, no intente resolverlo por si mismo.
  • Pagina 113 All manuals and user guides at all-guides.com 10. SOLUCION DE ERRORES SPANISH VERSION SO1-33007 10. SOLUCION DE ERRORES Problem Solution Error Message ERROR Papel atascado en la unidad Quite el papel atascado y coloque CORTAD cortadora. correctamente uno nuevo. **** Pulse la tecla [RESTART].
  • Pagina 114 All manuals and user guides at all-guides.com 10. SOLUCION DE ERRORES SPANISH VERSION SO1-33007 10. SOLUCION DE ERRORES Problema Solución No imprime 1. Comprobar que el papel y la cinta estén colocados correctamente. 2. Confirmar que el cabezal de impresión se encuentra en la posición correcta.
  • Pagina 115 All manuals and user guides at all-guides.com TEC Thermische Drukker B-480-QP SERIES Gebruikershandleiding...
  • Pagina 116: Samenvatting Veiligheid

    Herstel of wijzig deze uitrusting niet zelf. Indien een fout zich voordoet dat niet kan verholpen worden met behulp van de werkwijzen die in deze handleiding beschreven worden, zet dan het toestel af, haal de stekker uit het stopcontact en stel u in verbinding met een erkende TOSHIBA TEC verdeler voor bijstand. Betekenis van de symbolen Dit symbool geeft aan dat het een waarschuwing betreft.
  • Pagina 117 Raadgeving betreffende het onderhoud • Maak gebruik van onze onderhoudsdiensten. Doe minstens éénmaal per jaar beroep op een TOSHIBA TEC verantwoordelijke om de binnenzijde van het toestel te laten reinigen. Een overdadige ophoping van stof in het toestel kan aanleiding geven tot brand of een verkeerde werking van het toestel.
  • Pagina 118 All manuals and user guides at all-guides.com DUTCH VERSION NO1-33007 INHOUDSTAFEL Pagina 1. INLEIDING ..................N1- 1 1.1 Omschrijving van het typenummer ............N1- 2 1.2 Toebehoren ..................N1- 2 2. KENMERKEN ................N2- 1 2.1 Drukker ....................N2- 1 2.2 Optie ..................... N2- 2 2.3 Linten ....................
  • Pagina 119: Inleiding

    All manuals and user guides at all-guides.com 1. INLEIDING DUTCH VERSION NO1-33007 1. INLEIDING 1. INLEIDING Wij feliciteren u met uw keuze voor een thermische drukker TEC B-480. Deze allernieuwste drukker heeft een uitmuntende prijs/kwaliteitsverhouding. Hij is uitgerust met de meest vooruitstrevende technologie waaronder een drukkop die bijzonder duidelijke afdrukt met een hoge densiteit (12 punten/mm, 304.8 punten/inch) biedt tegen een snelheid van maximum 203.2 mm/sec.
  • Pagina 120: Omschrijving Van Typenummer

    All manuals and user guides at all-guides.com 1. INLEIDING DUTCH VERSION NO1-33007 1.1 Omschrijving van typenummer 1.1 Omschrijving van typenummer • B-482-TS10-QP Beschrijving van de naam van het model: B - 4 8 2 - T S 1 0 - Q P QP: Europese versie Uitvoer S: sequentiële mode...
  • Pagina 121: Kenmerken

    All manuals and user guides at all-guides.com 2. KENMERKEN DUTCH VERSION NO1-33007 2.1 Drukker 2. KENMERKEN 2.1 Drukker Model B-480-TS10-QP Naam Voeding AC 220V ~ 240V +10%, -15%, 50Mhz Verbruik 1.13A, 128W maximum (250mA, 23W: Standby) Temperatuurslimiet 5 C ~ 40 C Relatieve vochtigheid 25% ~ 85%RH (zonder condensatie) Drukkop...
  • Pagina 122: Opmerking

    600 m nog aan het drukker is. Externe diameter ø90 mm (max.) 2. Gebruik steeds door TOSHIBA TEC aanbevolen papier en linten om een betere drukkwaliteit te te bekomen en de levensduur van de drukkop te verhogen. 3. Iu snijmode moeten etiketten gebruikt...
  • Pagina 123 All manuals and user guides at all-guides.com 2. KENMERKEN DUTCH VERSION NO1-33007 2.4 Papier 2.4 Papier Etiket Gemarkeerd papier Zie opmerking 2. Zwarte stip op achterzijde Zwarte stip op achterzijde Stoplijn Soplijn Gemarkeerd papier Snijlijn Snijlijn Referentie Referentie Coordin. Coordin. Referentie Referentie Coordin.
  • Pagina 124: Overzicht

    All manuals and user guides at all-guides.com 3. OVERZICHT DUTCH VERSION NO1-33007 3.1 Voor - en Achterzijde 3. OVERZICHT 3.1 Voor - en Achterzijde Voorzijde Achterzijde Hoofddeksel Scherm (LCD) Toevoeraanduiding PCMCIA kaart slot (2 slots) Connectie voor seriële interface (RS-232C) Bedieningsbord Connectie voor parallelle Connectie voor I/O...
  • Pagina 125: Installatie Van De Drukker

    All manuals and user guides at all-guides.com 4. INSTALLATIE VAN DE DRUKKER DUTCH VERSION NO1-33007 4.1 Connectie van het electrisch snoer en de kabels 4. INSTALLATIE VAN DE DRUKKER 4.1 Connectie van het electrisch snoer en de kabels WAARSCHUWING: Zet eerst de printer af (schakelaar op "OFF") om het electrisch snoer en de kabels te installeren. Seriële I/F kabel (RS-232C) Parallelle I/F kabel (Centronics) Uitbreidingskabel I/O (Optie)
  • Pagina 126: Het Laden Van Papier

    All manuals and user guides at all-guides.com 5. HET LADEN VAN PAPIER DUTCH VERSION NO1-33007 5. HET LADEN VAN PAPIER 5. HET LADEN VAN PAPIER WAARSCHUWING: 1. Reak geen bewegende delen aan. Plaats de schakelaar op OFF om elke beweging te stoppen en het risiko dat vingers, juwelen, kleding enz.
  • Pagina 127 Indien de etiketten op de buitenkant van de rol staan, moeten de bovenplaten van de twee papierhouders verwijderd worden d.m.v. volgende procedure, zoniet is het risico op papieropstopping groot. Mocht u vragen hebben, stel u in verbinding met uw TOSHIBA TEC verantwoordelijke. N5-2...
  • Pagina 128: Verwijdering Van De Bovenplaten Van De Papierhouders Op De Medialeider

    All manuals and user guides at all-guides.com 5. HET LADEN VAN PAPIER DUTCH VERSION NO1-33007 5. HET LADEN VAN PAPIER Verwijdering van de bovenplaten van de papierhouders op de medialeider 1 Verwijder de twee T-4 X 8 vijzen om de medialeider los te maken van de drukker. Medialeider Vijs (T-4x8) Figuur 5-5...
  • Pagina 129: Instellingsprocedure Van De Zwarte Stip Sensor

    All manuals and user guides at all-guides.com 5. HET LADEN VAN PAPIER DUTCH VERSION NO1-33007 5. HET LADEN VAN PAPIER Instellingsprocedure van de zwarte stip sensor 1 Voer ongeveer 500 mm papier uit de drukker, vouw het om en duw het uiteinde onder de drukkop tot aan de papiersensor.
  • Pagina 130 All manuals and user guides at all-guides.com 5. HET LADEN VAN PAPIER DUTCH VERSION NO1-33007 5. HET LADEN VAN PAPIER 10. Het laden van het papier en de instelling van de papiersensor zijn voltooid. Batch type: Papier Figuur 5-9 OPMERKING: Plaats de selektieschakelaar op de STANDARD/STRIP positie.
  • Pagina 131 2. Indien de bovenste rand van het etiket zich rond de drukrol windt, moet u zich in verbinding stellen met een TOSHIBA TEC verantwoordelijke. 3. Voor het model met cutter mag de selektieschakelaar op beide posities geplaatst worden.
  • Pagina 132: Het Laden Van Lint

    All manuals and user guides at all-guides.com 6. HET LADEN VAN LINT DUTCH VERSION NO1-33007 6. HET LADEN VAN LINT 6. HET LADEN VAN LINT WAARSCHUWING: 1. Reak geen bewegende delen aan. Plaats de schakelaar op OFF om elke beweging te stoppen en het risiko dat vingers, juwelen, kleding enz.
  • Pagina 133: Verwittiging

    All manuals and user guides at all-guides.com 7. HET INBRENGEN VAN DE PCMCIA BORD IN OPTIE DUTCH VERSION NO1-33007 7. HET INBRENGEN VAN DE PCMCIA BORD IN OPTIE 7. HET INBRENGEN VAN DE PCMCIA BORD IN OPTIE VERWITTIGING: Zet de drukker af wanneer u het bord inbrengt of weghaalt. LET OP: Om de kaart te beschermen, verwijdert u best de statische elektriciteit van uw lichaam door de achterkap van de printer aan te raken, voor u het PCMCIA bord in handen neemt.
  • Pagina 134 Lees aandachtig deze handleiding en zorg ervoor dat de inhoud goed begrepen werd. Gebruik enkel de door TOSHIBA TEC aanbevolen media en etiketten. Het gebruik van andere media/etiketten kunnen aanleiding geven tot onleesbare barkodes en beschadiging van de drukkop. De gebruikte media moet zich in een perfekte staat bevinden.
  • Pagina 135: Onderhoud

    All manuals and user guides at all-guides.com 9. ONDERHOUD DUTCH VERSION NO1-33007 9.1 Reiniging 9. ONDERHOUD WAARSCHUWING: 1. Wees voorzichtig, de drukkop kan zeer heet worden. 2. Let op het mes voor verwondingen. 3. Reak geen bewegende delen aan. Plaats de schakelaar op OFF om elke beweging te stoppen en het risiko dat vingers, juwelen, kleding enz.
  • Pagina 136: Beschermingsvlakken En Deksels

    All manuals and user guides at all-guides.com 9. ONDERHOUD DUTCH VERSION NO1-33007 9.2 Beschermingsvlakken en deksels 9.2 Beschermingsvlakken en deksels Reinig de buitenzijde van de drukker met een droge doek of een doek die lichtjes met reinigingsmiddel werd bevochtigd. OPMERKING: Reinig het deksel van de drukker met een antistatisch reinigingsmiddel voor het onderhoud van geautomatiseerd bureaumateriaal.
  • Pagina 137: Reiniging Van De Snijmodule

    All manuals and user guides at all-guides.com 9. ONDERHOUD DUTCH VERSION NO1-33007 9.3 Papieropstopping Reiniging van de snijmodule WAARSCHUWING 1. Zet de drukker steeds af om de snijmodule te reinigen. 2. Let op het mes voor verwondingen. Het zwaaimes en het draaimes zijn beschikbaar in optie. Ze worden op dezelfde wijze gereinigd ongeacht verschillende afmetingen.
  • Pagina 138: Instelling Van De Drempelwaarde

    All manuals and user guides at all-guides.com 9. ONDERHOUD DUTCH VERSION NO1-33007 9.4 Instelling van de drempelwaarde 9.4 Instelling van de drempelwaarde De spatiesensor zorgt ervoor dat elk etiket automatisch op hetzelfde startpunt wordt bedrukt. Bij gebruik van voorgedrukte etiketten, kan het gebeuren dat, naargelang de inktsoort, de sensor er niet in slaagt de voedingsholte te detekteren.
  • Pagina 139 Automatische lint spaarmode De automatische lint spaarfunctie wordt actief wanneer de zone die niet bedrukt wordt meer dan 17 mm bedraagt. Wat deze functie betreft, stel u in verbinding met een TOSHIBA TEC verantwoordelijke. OPMERKING: Het lintverlies per lintbesparing varieert in overeenstemming met de verhouding tussen...
  • Pagina 140: Mogelijke Problemen

    All manuals and user guides at all-guides.com 10. MOGELIJKE PROBLEMEN DUTCH VERSION NO1-33007 10. MOGELIJKE PROBLEMEN 10. MOGELIJKE PROBLEMEN WAARSCHUWING: Mocht er zich een probleem voordoen dat met onderstaande tabel niet opgelost kan worden, probeer niet de drukker zelf te herstellen. Zet de drukker af, haal de stekker uit het stopkontakt en stel u in verbinding met een erkende dienstverlener.
  • Pagina 141: Snijmes Fout

    All manuals and user guides at all-guides.com 10. MOGELIJKE PROBLEMEN DUTCH VERSION NO1-33007 10. MOGELIJKE PROBLEMEN Foutmelding Probleem Oplossing Het papier is vastgelopen in de Verwijder het papier dat vastgelopen is SNIJMES FOUT snijmodule. en laad het onbeschadigde gedeelte op **** de manier.
  • Pagina 142 All manuals and user guides at all-guides.com 10. MOGELIJKE PROBLEMEN DUTCH VERSION NO1-33007 10. MOGELIJKE PROBLEMEN Probleem Oplossing Geen afdruk. Ga na of het papier of het lint korrekt ingebracht werd. Punten ontbreken in afdruk. De drukkop is vuil. Reinig de drukkop. Indien nodig, kontakteer een erkende dienstverlener.
  • Pagina 143 All manuals and user guides at all-guides.com TEC Stampanti termiche B-480-QP SERIE Manuale Utente...
  • Pagina 144: Significato Dei Simboli

    Non tentare di effettuare riparazioni sull'apparecchiatura. Nell'evenienza di un malfunzionamento che non possa essere corretto utilizzando le procedure descritte nel presente manuale, spegnere la stampante, disconnettere la presa elettrica e quindi contattare il rappresentante autorizzato TOSHIBA TEC per l'assistenza. Significato dei simboli Questo simbolo indica elementi che richiedono attenzione (incluse le cautele).
  • Pagina 145 Requisiti per la manutenzione • Utilizzate i nostri servizi di assistenza. Dopo l'acquisto della macchina, contattate il vostro rappresentante autorizzato TOSHIBA TEC per assistenza all'incirca una volta l'anno per la pulizia interna della macchina. In caso contrario, la polvere si accumulerà all'interno dell'apparecchiatura e potrà causare incendi o malfunzionamenti.
  • Pagina 146 Attenzione: 1. Questo manuale non puÚ essere copiato integralmente o in parte senza previa autorizzazione scritta della TOSHIBA TEC. 2. Il contenuto di questo manuale puÚ subire variazione senza preavviso. 3. Riferitevi al Vostro fornitore per qualunque richiesta di chiarimenti riguardo questo...
  • Pagina 147: Introduzione

    All manuals and user guides at all-guides.com 1. INTRODUZIONE ITALIAN VERSION IO1-33007 1. INTRODUZIONE 1. INTRODUZIONE Grazie per aver scelto la serie TEC B-480 stampante termico/trasferimento termico. Questa stampante di elevate prestazioni equipaggiata con hardware dell’ultima generazione, incluso le testine tipo NEAR EDGE (12 dots/mm, 304.8 dots/inch) che consentono una stampa nitida ad alte velocità...
  • Pagina 148: Modelli Utilizzabili

    All manuals and user guides at all-guides.com 1. INTRODUZIONE ITALIAN VERSION IO1-33007 1.1 Modelli utilizzabili 1.1 Modelli utilizzabili • B-482-TS10-QP Modello nome descrizione B - 4 8 2 - T S 1 0 - Q P QP: Versione Europea Modalità di stampa S: Batch Risoluzione T: 12 dots/mm...
  • Pagina 149: Specifiche

    All manuals and user guides at all-guides.com 2. SPECIFICHE ITALIAN VERSION IO1-33007 2.1 Stampante 2. SPECIFICHE 2.1 Stampante Modello B-480-TS10-QP Punti AC 220V ~ 240V +10%, -15%, 50Hz Alimentazione 1.13A, 128W massimo (standby: 250mA, 23W) Consumi 5 C ~ 40 C (41 F ~ 104 F) Temperature operative 25% ~ 85%RH (non condensata) Umidità...
  • Pagina 150: Opzioni

    ø90 mm (max.) Diametro esterno 2. Per assicurare la durata e la qualità di stampa utilizzate materiali raccomandati dalla TOSHIBA TEC. 3. Quando si usa la taglierina assicurasi la lunghezza dell’etichetta, incluso il gap, superi i 35mm. (Vedi Page 2-3.)
  • Pagina 151: Supporti

    All manuals and user guides at all-guides.com 2. SPECIFICHE ITALIAN VERSION IO1-33007 2.4 Supporti Cartellino Etichetta Riferito alla nota seguente 2.4 Supporti NOTA 2. Tacca nera Tacca nera (sul retro) (sul retro) Posizione Posizione Cartellino di stop di stop Posizione Posizione di taglio di taglio...
  • Pagina 152: Vista Generale

    All manuals and user guides at all-guides.com 3. VISTA GENERALE ITALIAN VERSION IO1-33007 3.1 Front/Rear View 3. VISTA GENERALE 3.1 Vista fronte/retro Vista frontale Vista posteriore Coperchio superiore Finestra di controllo Display messaggi (LCD) supporto/nastro Scheda PCMCIA Slot (2 slots) Connettore interfaccia seriale...
  • Pagina 153: Installazione

    All manuals and user guides at all-guides.com 4. INSTALLAZIONE ITALIAN VERSION IO1-33007 4.1 Connessione del cavo di alimentazione e comunicazione 4. INSTALLAZIONE 4.1 Connessione del cavo di alimentazione e comunicazione ATTENZIONE: Posizionare il pulsante di accensione sulla posizione OFF prima di collegare l’alimentazione alla stampante.
  • Pagina 154: Caricamento Dei Supporti Di Stampa

    All manuals and user guides at all-guides.com 5. Caricamento dei supporti di stampa ITALIAN VERSION IO1-33007 5. Caricamento dei supporti di stampa 5. Caricamento dei supporti di stampa ATTENZIONE: 1. Non toccare le parti in movimento. Per ridurre i rischi che dita, anelli, abbigliamento ecc., possano impigliarsi nei meccanismi in movimento, spegnete la stampante.
  • Pagina 155 All manuals and user guides at all-guides.com 5. Caricamento dei supporti di stampa ITALIAN VERSION IO1-33007 5. Caricamento dei supporti di stampa 5. Posizionare il supporto di stampa sul portarotoli. 6. Far passare il supporto di stampa dietro il braccio di smorzamento, quindi tirare verso il fronte della stampante.Riposizionare la flangia sul portarotoli facendo attenzione a non bloccare il supporto di stampa.
  • Pagina 156 All manuals and user guides at all-guides.com 5. Caricamento dei supporti di stampa ITALIAN VERSION IO1-33007 5. Caricamento dei supporti di stampa Rimozione delle guide carta superiori dal blocco guida carta 1 Rimuovere le due viti T-4x8 per sganciare il blocco guida carta. Guida carta Viti (T-4x8) Fig.
  • Pagina 157 All manuals and user guides at all-guides.com 5. Caricamento dei supporti di stampa ITALIAN VERSION IO1-33007 5. Caricamento dei supporti di stampa Un sistema semplice per centrare il sensore della tacca nera 1 Estrarre il supporto di stampa per circa 500mm dal fronte della stampante, ripiegare il supporto su se stesso, e reinserirlo nella stampante passando sotto la testina, ora la tacca nera è...
  • Pagina 158 All manuals and user guides at all-guides.com 5. Caricamento dei supporti di stampa ITALIAN VERSION IO1-33007 5. Caricamento dei supporti di stampa 10. Ora il supporto di stampa e i sensori sono posizionati. Modalità Batch: Supporto di stampa Fig. 5-9 NOTA: Posizionare lo switch di selzione Standard/strip nella corretta posizione.
  • Pagina 159 1. Assicuratevi di non tagliare direttamente sulle etichette, l’eventuale deposito di collante sulle lame può causare difetti di taglio. 2. Se il supporto dovesse incepparsi nella taglierina, contattate lail centro assistenza TOSHIBA TEC. 3. Per il modello con taglierina lo switch può essere settato in entrambe le modalità.
  • Pagina 160: Caricamento Nastro Di Stampa

    All manuals and user guides at all-guides.com 6. Caricamento nastro di stampa ITALIAN VERSION IO1-33007 6. LOADING THE RIBBON 6. Caricamento nastro di stampa ATTENZIONE: 1. Non toccare le parti in movimento. Per ridurre i rischi che dita, anelli, abbigliamento ecc., possano impigliarsi nei meccanismi in movimento, spegnete la stampante.
  • Pagina 161: Inserimento Della Pcmcia (Opzionale)

    All manuals and user guides at all-guides.com 7. Inserimento della flash memory card (opzionale) ITALIAN VERSION IO1-33007 7. Inserimento della PCMCIA (opzionale) 7. Inserimento della PCMCIA (opzionale) ATTENZIONE: Spegnere la stampante prima di inserire o rimuovere la scheda. CAUTELE: Per non danneggiare la scheda PCMCIA prima manegiiarla toccare il pannello posteriore della stampante per scaricare il corpo dalle correnti statiche.
  • Pagina 162: Utilizzo E Manutenzione Dei Supporti E Nastri

    • Alcuni inchiostri contengono sostenze chimiche che abbreviano la vita della testina. Non utilizzare etichette con prestampe effettuate con inchiostri che contengano carbonato di calcio (CaCO ) e kaolin , 2SiO , 2H Per ulteriori informazioni contattate il Vostro fornitore locale o la più vicina filale TOSHIBA TEC. I8-1...
  • Pagina 163: Manutenzione Generale

    Maggiore è l’utilizzo della stampante, più frequentemente deve essere pulita. Basso utilizzo = settimanale, alto utilizzo= giornaliero. Nella stampante non è inserito inessun attrezzo per la pulizia della testina.Contattate la più vicina filale TOSHIBA TEC per informazioni. 1. Spegnere la stampante. 2. Aprire il coperchio.
  • Pagina 164: Coperchio E Pannelli

    All manuals and user guides at all-guides.com 9. Manutenzione generale ITALIAN VERSION IO1-33007 9.2 Coperchio e pannelli 9.2 Coperchio e pannelli La scocca deve essere pulita con un panno asciutto o lievemante imbevuto con detergenti non aggressivi. NOTA: Pulire la scocca con panni antistatici per materiali elettronici. ATTENZIONE: 1.
  • Pagina 165 All manuals and user guides at all-guides.com 9. Manutenzione generale ITALIAN VERSION IO1-33007 9.3 Rimozione delle etichette inceppate Pulizia della taglierina ATTENZIONE: 1. Assicuratevi che la stampante sia spenta. 2. Le lame della taglirina sono affilate. Prendete delle preacuzioni per evitare di ferirvi. La taglierina rotativa o diagonale sono disponibili come parti opzionali.
  • Pagina 166: Settaggio Dei Sensori

    All manuals and user guides at all-guides.com 9. Manutenzione generale ITALIAN VERSION IO1-33007 9.4 Settaggio dei sensori 9.4 Settaggio dei sensori Per mantenere il passo durante la stampa, si utilizza il sensore per il gap. Il sensore rileva la differenza di luce fra il supporto si stampa ed il gap.
  • Pagina 167 Modalità automatica di SAVE RIBBON La modalità automatica di save ribbon avviene se vi sono almeno 17mm di area non stampata. Per l’utilizzo di questa modalità contattare la TOSHIBA TEC . NOTA: Il consumo del nastro varia in accordo alla velocità ed al volume di nastro riavvolto come indicato nella seguente tabella: Velocità...
  • Pagina 168: Risoluzione Dei Problemi

    10. Risoluzione dei problemi 10. Risoluzione dei problemi ATTENZIONE: Nel caso non riscontriate il problema nelle pagine suguenti, o qusto non venisse risolto spegnere la stampante, scollegare il cavo di alimentazione e contattare il servizio di assistenza TOSHIBA TEC. Problema Soluzione...
  • Pagina 169 2. Sostituire la flash memory card e ritentare. 3. Spegnere la stampante e contattare il centro di assistenza TOSHIBA TEC. E’ stato riscontrato un errore durante FORMAT ER- 1. Spegnere la stampante, resettare la la formattazione della flash memory flash memory card e ritentare.
  • Pagina 170 3. Controllare i cavi di connessione. Mancano dei punti nella stampa. Testina sporca. Pulire la testina. Se necessario contattare il centro di assistenza TOSHIBA TEC. Stampe non nitide. 1. Testina sporca. Pulire la testina. 2. Nastro errato o rovinato.

Inhoudsopgave