Inhoudsopgave
Advertenties
4. Technical data
Mains voltage: .........................220-240 V~ 50 Hz
Power: ....................................................... 750 W
Stroke rate: .......................................0-2800 min
Stroke height: ........................................... 20 mm
Cutting depth in wood: ........................... 150 mm
Cutting depth in iron: ................................ 10 mm
Maximum saw blade width: ..................... 1.5 mm
Protection class: ............................................ II/
Weight: .......................................................2.6 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
sound pressure level ..................... 86.3 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ....................... 97.3 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Cutting wooden boards
Vibration emission value ah = 18.67 m/s²
Uncertainty K = 1.5 m/s
Cutting wooden beams
Vibration emission value ah = 16.36 m/s
Uncertainty K = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Anleitung_TE_AP_750_E_SPK13.indb 14
Anleitung_TE_AP_750_E_SPK13.indb 14
GB
-1
2
2
2
- 14 -
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 2)
Always switch off and unplug the multi-saw before
working on the machine or changing the saw
blade.
Turn the ring (a) on the blade holder (5) as shown
in Fig. 2 until the blade (3) lets itself be slipped
into the slot of the blade holder (5).
When you now let go of the ring (a) again, the ring
(a) should return to its starting position.
If this fails to happen, try turning the ring (a) by
hand into its starting position.
Pull on the blade to check whether it sits tightly in
the holder.
30.05.2023 10:25:46
30.05.2023 10:25:46
Advertenties
Inhoudsopgave
