Inhoudsopgave
Advertenties
• Connection in the upper part of the
M
device
.
Prepare the device for electrical connection
in the upper part.
1. Break through the marked inlet aperture in
the rear plate (a) of the device.
2. Shorten the cable grommet for providing
the seal (b), wet it on the inside with a
lubricating agent for better fitting (ease of
sliding), and fit it in the back plate (c).
3. Release terminal block (d).
4. Fit the terminal block (e) in the upper part
of the device. Care is to be taken to
ensure that the switching leads do not
project over the back plate of the device.
1
1
Carry out the electrical connection
1
2
2
To provide protection against water
2
3
penetration, the cable grommet provided
3
3
must be fitted in accordance with
4
4
1
4
the dimensions respected.
5
5
5
2
Establish the electrical connection in
6
6
K
6
3
accordance with
.
7
7
7
4
1
8
Concluding the installation
8
8
1
5
2
Open the 3-way shutoff valve.
9
9
1
2
9
6
3
10
Secure the lower part of the back plate.
10
2
10
3
7
4
11
11
3
Fit the lower fixing screw.
11
4
8
5
12
4
12
12
5
9
6
• • • • • Only for water connection on surface
13
5
13
13
6
10
With the water connection on the
7
14
6
14
14
7
11
surface, break through the knock-out
8
1
15
7
15
15
8
apertures
in the cover in an
12
9
1
2
16
8
16
appropriately clean manner, using a file if
16
9
13
10
2
3
necessary. The guide pieces
17
9
17
17
10
14
11
3
with the device should be engaged in the
4
10
18
18
18
11
15
penetration apertures.
12
4
5
11
19
19
19
12
16
5
• • • • • Only for installation over-sink
13
6
12
20
20
20
13
17
Bring the inside toothed bar into the
6
14
7
13
21
21
21
14
middle position.
18
7
15
8
14
22
22
22
Fit the cover, secure the screw, and
15
19
8
16
9
15
23
23
close the cover cap.
23
16
20
9
17
10
Turn the shower comfort switch and po-
16
24
24
24
17
21
10
18
wer selector switch to the left and right
1
11
17
18
1
22
stops (internal setting lever will engage).
11
19
2
12
18
2
19
23
12
20
• • • • • Only for installation under-sink
3
13
19
3
20
24
13
21
4
20
14
If installed with the cover rotated, the
4
21
14
22
5
device has the protection mode IP 24
15
21
22
5
15
(protected against spray water).
23
6
16
22
6
23
16
24
7
Move the snap nut from the bottom to
23
17
7
24
17
the top.
8
18
24
8
Cover over the cover label (Stiebel
18
9
19
9
Eltron, Temperature trail and rating
19
10
20
plate) using the adhesive label supplied
10
20
11
21
(backing film serves as fitting aid):
11
21
12
a Remove protective film
22
12
b Align the label
22
13
23
c Press the label in place
13
23
14
24
d Draw off the backing film
14
24
15
e Press the label in place
15
f Cover over IP 25 on the rating plate
16
16
with IP 24
17
g Move the lever to the left
17
18
engagement position.
18
Mount cover, tighten screw and close
19
19
the cover cap.
20
Rotate the shower comfort switch and
20
21
power selector switch to the left and
21
22
right stops (inside setting lever engages).
22
23
14
23
24
24
Initial operation
1. Fit device in position.
2. Fill device with water.
3. Engage the power selector switch
shower comfort switch
to the left and right and then bring it into
the basic setting.
4. Connect the fuses.
5. Check function.
Handing the device over to the
customer
1. Select basic position
2. Explain the positions of the power
selector switch and the shower comfort
switch (see page 11).
If the water pressure is low, move
the shower comfort switch into the
engagement position
M
and
selector switch to position
1
3. Draw the attention of the user to the risk
2
of scalding.
3
4. Indicate the location of the short operating
N
instructions in the cover (3 a), if necessary
4
choose a different language (see the
5
middle part of these operating and
6
installation instructions).
7
8
Accessories
O
9
Two-handle pressure fittings
10
– Kitchen fitting WKMD,
Order No. 07 09 17
11
12
– Bath fitting WBMD,
Order No. 07 09 18
provided
13
– Grohe Relaxa hand-held shower, plastic,
14
chrome-plated with especially low
15
P
pressure loss (0.02 MPa at 10 l/min),
16
Order No. 06 85 21.
17
Area of use:
18
With particularly low supply pressure in
the water installation, a clearly improved
19
temperature stability will be achieved
20
when showering.
21
– Load-shedding relay LR 1-A,
22
Order No. 00 17 86
Q
23
Priority circuit of the DHB with
24
simultaneous operation, for example, of
electrical storage heaters.
For connection of LR 1-A, see
– Pipe set
Gas device replacement, for DHB - Si,
Order No. 22 05 10
Surface connection with cold water on the
left and hot water on the right side.
– Pipe set
Installation under-sink, for DHB - Si,
Order No. 07 05 65
Connections: Surface fitting, G
– Set of two units, water blanking plugs
I
G ½
Required for water installation with fittings
on surface or beneath it, not with WKMD
or WBMD.
A
B
by rotating it
A
B
and
.
1
and set the power
2
.
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
K
.
1
2
3
/
, top.
3
8
4
, Order No. 07 43 26
5
6
7
8
9
10
11
12
13
14
– Surface installation kit
Order No. 07 40 19
- 2 pieces, blanking disks G ½
- 2 pieces, connection piece ½" with
and
insert for solder connection
Not necessary for Stiebel Eltron WKMD
and WBMD tap fittings.
3. Guarantee
For guarantees please refer to the respective
terms and conditions of supply for your
country.
The installation, electrical connection
and first operation of this appliance
should be carried out by a qualified
installer.
The company does not accept liability
for failure of any goods supplied which
have not been installed and operated in
accordance with the manufacturer's
instructions.
4. Environment and
recycling
Dispose of packing material and appliances
The dispose of the packing material and the
appliances must be done according to the
local recycling laws and regulations.
5. Servicing instructions
R
qualified installer
Removing the components from the back
panel:
1. Release the central fastening screw
assembly, item (a).
2. Pivot the module carrying components
out of the back panel.
Fitting the disengaged toothed bar
1. Rotate the toothed wheel (b) in the
clockwise direction by hand, as far as the
stop.
2. Slide the toothed bar (c) in from above.
Replace the safety pressure limit switch
(AD 3).
1. Press the engagement hooks (d) in the
direction of the arrow
2. Rotate AD 3, item (e) counter-clockwise
(bayonet fitting).
R
c
b
a
1
1
2
2
3
3
I
4
4
5
5
6
6
7
.
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
21
21
22
22
23
23
24
24
e
d
Advertenties
Inhoudsopgave
