Inhoudsopgave
Advertenties
• If you suffer from an irregular heartbeat (arrhythmia, see
«Section 4.»), measurements taken with this instrument should
only be evaluated after consultation with your doctor.
• The pulse display is not suitable for checking the
frequency of heart pacemakers!
How do I evaluate my blood pressure?
Table for classifying blood pressure values in adults in accordance
with the World Health Organisation (WHO) in 2003. Data in mmHg.
Range
Systolic
blood pressure
100
too low
1. blood pressure
100 - 120
optimum
2. blood pressure
120 - 130
normal
3. blood pressure
130 - 140
slightly high
4. blood pressure
140 - 160
too high
5. blood pressure
160 - 180
far too high
6. blood pressure
180
dangerously
high
The higher value is the one that determines the evaluation.
Example: a readout value between 150/85 or 120/98 mmHg indi-
cates «blood pressure too high».
The slot-in card 3 on the front of the instrument shows ranges
1-6 in the Table.
2. Using the Instrument for the First Time
Activating the fitted batteries
Pull out the protective strip projecting from the battery compart-
ment 7.
Setting the date and time
1. After the new batteries are fitted, the year number flashes in
the display. You can set the year by pressing the M-button AT.
To confirm and then set the month, press the time button AL.
BP A100 Plus
Diastolic
Recommendation
60
Consult your doctor
60 - 80
Self-check
Self-check
80 - 85
85 - 90
Consult your doctor
90 - 100
Seek medical advice
Seek medical advice
100 - 110
110
Urgently seek
medical advice!
2. You can now set the month using the M-button. Press the time
button to confirm and then set the day.
3. Please follow the instructions above to set the day, hour and
minutes.
4. Once you have set the minutes and pressed the time button, the
date and time are set and the time is displayed.
5. If you want to change the date and time, press and hold the time
button down for approx. 3 seconds until the year number starts
to flash. Now you can enter the new values as described above.
Selecting the correct cuff
Microlife offers 3 different cuff sizes: S, M and L. Select the cuff
size to match the circumference of your upper arms (measured by
close fitting in the centre of the upper arm). M is the correct size
for most people.
Cuff size
for circumference of upper arm
S
17 - 22 cm (6.75 - 8.75 inches)
M
22 - 32 cm (8.75 - 12.5 inches)
L
32 - 42 cm (12.5 - 16.5 inches)
Only use Microlife cuffs.
Contact Microlife Service if the enclosed cuff 8 does not fit.
Connect the cuff to the instrument by inserting the cuff
connector 9 into the cuff socket 4 as far as it will go.
Selecting the measuring mode: standard or MAM mode
This instrument enables you to select either standard (standard
single measurement) or MAM mode (automatic triple measure-
ment). To select standard mode, slide the MAM switch AK on the
side of the instrument downwards to position «1» and to select
MAM mode, slide this switch upwards to position «3».
MAM Mode
• In MAM mode, 3 measurements are automatically taken in
succession and the result is then automatically analyzed and
displayed. Because blood pressure constantly fluctuates, a result
determined in this way is more reliable than one produced by a
single measurement.
• After pressing the ON/OFF button 1, the selected MAM mode
appears in the display as the MAM-symbol BK.
• The bottom right hand section of the display shows a 1, 2 or 3 to
indicate which of the 3 measurements is currently being taken.
EN
3
Advertenties
Hoofdstukken
Inhoudsopgave
