Inhoudsopgave
Advertenties
10
Speaker Connection
NOTE: The following text describes both binding post and plug-in
connections. DO NOT use both connection methods in combination
to connect multiple speakers.
Turn off all the components in the system before connecting the speakers.
The unit has color-coded binding post type speaker connectors on the
back panel (except in European Community countries where their use
is not permitted). These connectors accept bare wire, connector lugs, or
dual banana type connectors.
Route the wire from the unit to the speakers. Give yourself enough slack so
you can move the components to allow access to the speaker connectors.
If you are using dual banana plugs, connect them to the wires and then
plug into the backs of the binding posts. The thumbscrews of the binding
posts should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are
attaching bare wires directly to the binding posts, separate the wire
conductors and strip the insulation from the end of each conductor. Be
careful not to cut into the wire strands. Unscrew (turn counterclockwise)
the binding post thumbscrews. Place the connector lug or wire around
the binding post shaft. Turn the thumbscrews clockwise to clamp the
connector lug or wire firmly in place.
NOTE: Be sure there are no loose wire strands that could touch
adjacent wires or connectors.
IR Remote Sensor 4
This remote sensor window receives IR commands from the remote
control. Please do not block this sensor.
Headphone Output 3
The headphone output allows you to connect headphones for private
listening. This output accepts a standard 3.5 mm (1/8") mini stereo
headphone connector. Plugging in a set of headphones does not cut
off the signal to the outputs.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.
aptX™ HD Bluetooth
Connection 0
0
The Bluetooth Antenna
on the back panel is for wireless streaming via
Bluetooth, from your device (i.e. mobile phones, tablets or computers).
From your device, look for "Rotel Bluetooth" and connect to it. Connection
is normally automatic, but if prompted for a password, please enter "0000"
on your device. The amplifier supports both traditional Bluetooth, AAC
and aptX™ HD Bluetooth audio streaming.
A11MKII Stereo Integrated Amplifier
Power Control -
Power Control could make the A11MKII go to standby mode or automatically
turn off when there is no signal or operation to the A11MKII.
When the slider is set to the SIGNAL SENSE position, the A11MKII will
check if a digital signal is present on the currently selected Signal Sense
input. If there is no digital audio detected for 10 minutes, the unit will
enter Signal Sense Power Mode. When in Signal Sense Power Mode
and the unit detects digital audio, the unit will automatically power on.
When the slider on the APD (AUTO POWER DOWN) position, the A11MKII
will automatically power off to standby mode if there is no audio signal
for 20 minnutes. The auto power off timer will be restarted if changes
are made to the volume, source or playback.
To disable above functions, push the slider to the NONE position.
NOTE: When the A11MKII enters standby mode via the remote
control, the Signal Sense function will not operate until the unit
detects the audio has stopped for the minimum 10 minute time-out
period. This prevents the unit from immediately powering back on
if there is still active audio playing.
NOTE: When the SIGNAL SENSE function is activated the A11MKII
will consume additional power in Signal Sense Power mode.
SERVICE Connector =
The SERVICE connector is for use by Authorized Service Centers only.
Audio Controls
Volume Control 8C
Turn the controls clockwise to increase the volume, or counter clockwise
to decrease the volume. From the remote control press the volume +
or - button
to turn the volume up or down. Press the
C
completely mute the volume.
Balance Control 5
The Balance Control adjusts the left-to-right balance of the sound
output. Normally the control should be left in the center position. In
some situations, typically when the main listening position is not ideally
centered between the speakers, it may be necessary to adjust the control
to achieve proper left-to-right balance. Turning the Balance rotary knob
5
counter-clockwise shifts the sound balance to the left. Turning the
Balance rotary knob
5
clockwise shifts the sound balance to the right.
Bass and Treble Controls 67
Turn the Bass / Treble rotary knobs
treble output. Turn the Bass / Treble rotary knobs
to decrease the bass or treble output.
A properly setup high-performance audio system produces the most
natural sound with little or no adjustment of the tone controls. Use these
controls sparingly. Be particularly careful when turning the controls up
(clockwise). This increases the power output in the bass or treble range,
increasing the load on the amplifier and speakers.
button
67
clockwise to increase the bass or
67
counterclockwise
to
D
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
