Technical Data - Bosch GWS Professional 9-115 Oorspronkelijke Gebruiksaanwijzing
Verberg thumbnails
Zie ook voor GWS Professional 9-115:
- Oorspronkelijke gebruiksaanwijzing (429 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
OBJ_BUCH-2538-001.book Page 16 Thursday, July 2, 2015 11:38 AM
16 | English
Delivery Scope
Angle grinder, protection guard, auxiliary handle.
Special protection guards, application tools and other acces-
sories shown or described are not part of the standard deliv-
ery scope.
A complete overview of accessories can be found in our ac-
cessories program.
Intended Use
The machine is intended for roughing metal, stone and ceram-
ic materials and for drilling tiles.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
Together with the hand guard (accessory), the machine can
be used for brushing and grinding/sanding with elastic sand-
ing plates.
The machine is suitable only for working without water.
Technical Data
The technical data of the machine are listed in the table on
page 264–266.
The values given are valid for a nominal voltage [U] of 230 V.
For different voltages and models for specific countries,
these values can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3.
Mounting and Operation
The following table indicates the action objectives for mounting and operation of the power tool. The instructions for each action
objective are shown aside. Depending on the type of application, various instruction combinations are required. Observe the
safety instructions.
Action
Grinding, preparation
Cutting, preparation
1 609 92A 14C | (2.7.15)
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 02.07.2015
Noise/Vibration Information
The measured values of the machine are listed in the table on
page 264–266.
Sound emission values determined according to
EN 60745-2-3.
Vibration total values a
determined according to EN 60745-2-3.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Figure
1
30°
2
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
(triax vector sum) and uncertainty K
h
Please observe
Bosch Power Tools
Page
267 – 268
269 – 270
Advertenties
Inhoudsopgave
