Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Alternative:
Manufacturer:
Gold Mark (China) Limited
Unit 1706, 17/F., Vanta Industrial
Centre, 21-33 Tai Lin Pai Road,
Kwai Chung, N.T. Hong Kong
Type
Adapter 9050A-1 (VI)
Input voltage:
100 – 240 V
Input AC frequency:
50/60 Hz
Output voltage:
12.0 V
Output current:
1.2 A
Output power:
14.4 W
Average active efficiency:
84.28 %
Efficiency at a
low load (10 %):
74.28 %
No-load power consumption: 0.075 W
Operating conditions
Ambient temperature:
0°C – +40°C
The appliance is safety insulated and radio screened. It meets
the requirements of EU Electromagnetic Compatibility Directive
2014/30/EU and Machinery Directive 2006/42/EC.
Operation
Preparation
Keep the packaging material for safe storage or trans-
port later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Please note that we perform quality tests on all of our
products. Therefore, you may find small synthetic hair
on the blade set or on the machine. However, we assure
you that your clipper and cutting blade / blade set are
unused.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated
on the nameplate.
Mains operation
1. Connect the plug-in transformer to the socket (Fig. 2)
2. Switch on the appliance using the on/off switch (Fig. 3ⓐ) and,
after use, switch it off again (Fig. 3ⓑ).
Operation
Cutting with the attachment comb
The appliance can also be operated with attachment combs.
Attachment combs can be used to extend the cutting length range.
Attaching/removing the attachment comb
1. Fit the attachment comb onto the bottom edge of the blade
set (Fig. 4ⓐ) and push it over the cutting edge of the bottom
blade until it locks (Fig. 4ⓑ).
2. Draw the attachment comb towards the cutting edge of the
bottom blade (Fig. 5) and remove it from the blade set.
Maintenance
Warning! Injuries and material damage due to incor-
rect handling.
f Before performing any cleaning and maintenance
work, switch off the device and disconnect it from
the power supply.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and
accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
·
Accessories are available from our dealer.
·
Spare parts are available from our service centre.
f Remove the attachment comb (Fig. 5) after every use and lift
the blade set out of the casing (Fig. 6). Use the cleaning brush
to remove any cut hairs from the housing opening and from
the blade set (Fig. 9).
Caution! Injuries due to incorrect handling.
f The blade set must not be unscrewed.
f The top blade must not be pushed out completely!
f Only wipe the appliance with a soft, slightly damp cloth.
f Push the top blade to the side (Fig. 9ⓐ) and remove cut hairs
from the top and bottom blade using the cleaning brush. After
cleaning, return the top blade to its initial position (Fig. 9ⓑ).
The top blade should be aligned in the centre of the bottom
blade.
f Oil the blade set with the blade set oil (Fig. 10).
f Reattach the blade set after cleaning (Fig. 7/8). Switch the
appliance on briefly (approx. 10 seconds) to ensure the oil film
is evenly distributed.
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
11
ar
Advertenties
Inhoudsopgave
