Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
•
Do not use non-approved accessories on the
product. Accessories can decrease the protective
capabilities.
•
Make sure that the saw protection of the protective
clothes overlaps the saw protection of the safety
boot.
•
For best performance and safety, do maintenance
on the product regularly. Refer to
on the product on page 4 .
•
Clean the product immediately in case it has been
subjected to petrol, oil, grease or other flammable
materials. Fire hazard!
•
Make sure that the product is not damaged and
there are no other defects, such as cracks. The
To do maintenance on the product
•
The service life of the product varies with the type of
use. The service life depends fully on the condition
of the product. To achieve maximum service life,
the product must be maintained and kept in storage
correctly.
•
Clean the product with damp cloth or sponge. Do not
use polishing or corroding cleaning agents.
•
When the product is wet, air dry slowly and away
from heat sources such as radiators or direct
sunlight.
•
Impregnate the safety shoe regularly. Use wax or
silicone based shoe care product or dubbin.
•
In the event of a repair being carried out to the outer
material, do not sew into the protective material
since this can reduce the protective qualities.
Adhesive must not be used when carrying out
repairs as it may affect the protective material and
decrease its protective qualities.
•
Store the product on a level surface, standing up in a
dark and dry area.
Disposal
•
Obey national regulations.
•
Use the local recycling system.
These products Style 910, Style 910A, Style 930,
Style 931, Style, 932, Style 933, Style 934, Style 940
conforms to the applicable EU regulations and complies
with basic requirements and standards:
•
EU regulation 2016/425
•
EN ISO 17249:2013
CE Marking
Notified body responsible for type examination and
carrying out annual Module C2 assessment of products
covered by this user information in accordance with EU
4
To do maintenance
Maintenance
Compliance and approvals
product should be scrapped and not used again
if the protective material has been damaged,
incorrectly cleaned or altered from its original shape.
The protective qualities may be reduced in these
cases.
•
Keep the product away from sharp objects, acids,
oils, solvents, fuels and animal droppings.
•
The heat resistance of the outsole (PU) is 120°C.
•
The product is supplied and tested with insoles. If
the insole is to be replaced, always use original
spare parts.
•
If you feel uncertain after reading these instructions,
speak to your Husqvarna dealer before continuing.
Service life of the product
The service life of the product varies with the type of
use. In professional logging the maximum service life
of the product is 1 year. The maximum service life of
the product is 5 years. Maximum service life can only
be achieved if the product is used occasionally and non-
professionally. To achieve maximum service life, the
product must be kept in storage correctly.
The product must be discarded after a maximum of 5
years of use.
The actual service life depends fully on the condition of
the product.
Extreme conditions during operation can shorten the
service life to a single use only. If the product is
damaged before its first use, for example during
transportation, it must be discarded immediately and not
used.
CAUTION:
not use it again if the product:
•
has been damaged.
•
has been washed incorrectly.
•
has been altered from its original shape.
Regulation 2016/425 is SMP Svensk Maskinprovning
AB, Box 4053, SE-904 03 Umeå, Sweden. Notified Body
Number 0404, as shown next to the CE mark.
The full text of the EU declaration of conformity
is available at the following internet address:
www.husqvarna.com; search for the product.
Responsible manufacturer: Husqvarna AB,
Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel:
+46-36-146500.
Dispose the product and do
2352 - 001 - 06.12.2023
Advertenties
Inhoudsopgave
