Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
0
Switching on: Slide the switch-on lock (8) in the
direction of the arrow and press the trigger (7).
Switching off: release the trigger switch (7).
7.5
Working instructions
Grinding, sanding, polishing or using wire
brushes: Press down the machine evenly and
move it from side to side over the surface.
Routing: Press down the machine evenly.
Separating:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed suit-
able for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
8. Cleaning
8.1
Motor cleaning
To clean the motor, apply jets of compressed air
through the rear ventilation slots of the machine
regularly, frequently and thoroughly. The machine
must be held firmly in this case.
9. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
A Collets (including nut)
dia. 3 mm = 631947000
dia. 1/8" = 631948000
dia. 6 mm = 631945000
dia. 1/4" = 631949000
dia. 8 mm = 631946000
B Clamping frame 628329000 for clamping
during work with flexible shafts, including:
C Clamping bracket 627107000 for safe securing to
the work bench (tighten clamping screw).
D Mounted points for fine grinding work on metal.
E Cutting wheel for fine cutting and grinding work on
metal.
For a complete range of accessories, see
www.metabo.com or the catalogue.
10. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
7 7 8
8
I
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
returned for environmentally compatible recycling.
12. Technical specifications
Explanation of details on page 3. Subject to
changes serving technical progress.
n
= No-load speed (maximum speed)
n
= On-load speed
1
P
= Nominal power input
1
P
= Power output
2
D
= Maximum grinding wheel diameter
max
T
= Maximum thickness of bonded grinding
max
wheels
d
= Collet bore of the collet chuck
m
= Weight without mains cable
L
= maximum insertion depth
max
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
= Vibration emission level
h, SG
K
= Uncertainty (vibration)
h,SG
U
= Unbalance
M
Typical A-effective perceived sound levels::
L
= Sound pressure level
pA
ENGLISH en
15
Advertenties
Inhoudsopgave
