Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
CAUTION:
This cleaner is for dry use only.
CAUTION:
This cleaner is for indoor use only.
CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
CAUTION:
During operation, be conscious
of the vacuum cleaner on your back. You may
lose your balance if the vacuum cleaner body bumps
against a wall or the hose is hooked by an obstacle.
1.
Shoulder the vacuum cleaner body and fas-
ten lower and upper belts. Adjust the tightness as
necessary.
► Fig.27
2.
Press
button to start vacuuming. To change
the suction power, press
cleaner is running. The suction power switches between
normal (1) and higher (2) suction power. Press
ton to stop.
► Fig.28
During the operation, hook the switch box on the lower
belt or the D-ring.
► Fig.29
Replace the filter bag when it becomes full. Open
3.
the lid and take out the filter bag. Pull the strip on the
side of the opening to shut the filter bag and dispose of
the filter bag in whole.
► Fig.30: 1. Strip
When using a dust bag, take out the dust bag and dis-
pose of the dust by releasing the latch.
► Fig.31: 1. Latch
Periodically check the filter bag if it is
NOTICE:
full. Continuous use with the filter bag full results in
reduced suction power.
Do not use an used filter bag. The filter
NOTICE:
bag is designed for single use. Using filter bag repeat-
edly may cause clogging of the filter and results in
damage to the cleaner. If you want to use the bag
repeatedly, use a dust bag.
WIRELESS ACTIVATION
FUNCTION
What you can do with the wireless
activation function
The wireless activation function enables clean and
comfortable operation. By connecting a supported tool
to the cleaner, you can run the cleaner automatically
along with the switch operation of the tool.
► Fig.32
button while the vacuum
but-
NOTICE:
Be sure to refer to the instruction man-
ual of the tool when using the cleaner with wire-
less activation function.
NOTICE:
Do not disassemble or tamper with the
wireless unit.
NOTICE:
To prevent dust coming into the slot
of the wireless unit, always close the lid securely
during operation and storage.
NOTICE:
Do not remove the wireless unit while
the power is being supplied. Doing so may cause a
malfunction of the wireless unit.
NOTICE:
Do not press the wireless activation
button too hard and/or press the button with an
object with a sharp edge.
NOTE: Wireless activation needs Makita tools
equipped with the wireless unit.
NOTE: Prior to the initial use of the wireless activa-
tion function with each tool, the tool registration is
required. Once the registration is finished with the
tool, the re-registration is not required unless it is
cancelled.
NOTE: Before registration, be sure that the wireless
unit is properly inserted.
NOTE: One wireless unit can register up to 10 links
with other wireless units. If more than 10 other wire-
less units are registered to one wireless unit, the one
registered earliest will be cancelled automatically.
NOTE: The position of the wireless activation button
varies depending on the tool.
NOTE: The cleaner also starts by pressing
when the stand-by switch is set to " I (ON)".
However the
button will not work when the wire-
less activation function is used.
Installing the wireless unit
Place the cleaner on a flat and
CAUTION:
stable surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the cleaner
before installing the wireless unit. Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such
as a metallic part, before picking up the wireless
unit.
NOTICE:
When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
Open the lid on the cleaner as shown in the figure.
1.
► Fig.33: 1. Lid
2.
Insert the wireless unit to the slot and then close
the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.34: 1. Wireless unit 2. Projection 3. Lid
17 ENGLISH
button
Advertenties
Inhoudsopgave
