Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Adjusting the guard (Figure J)
To adjust the tool to the task at hand, the guard hood can be
adjusted by 12 notches on 360° without a tool.
CAUTION!
Risk of injury! Wear protective gloves.
Pull out the mains plug.
Turn guard hood opposite to the direction-of-rotation arrow
on the gear head to the required position.
Work instructions
NOTE
When the power tool is switched off, the grinding tool continues
running briefly.
Rough-grinding
WARNING!
Never use cutting-off wheels for rough-grinding.
–
Angle of wheel 20–40° for best cutting performance.
–
Applying moderate pressure, move the angle grinder
backwards and forwards. As a result, the workpiece will not
become too hot and there will be no discoloration; nor will
there be any grooves.
Cut-off grinding (Figure K)
WARNING!
A special cutting guard must be used for cutting.
See manufacturer's accessories catalogue.
–
Do not press, tilt or oscillate the power tool.
Otherwise, there is a risk of the angle grinder jumping
uncontrollably out of the groove.
–
The angle grinder must always be operated backwards.
–
Adjust the feed to the material which is to be cut: the harder
the material, the slower the feed.
Maintenance and care
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Cleaning
WARNING!
If metals are ground or cut over a prolonged period, conductive
dust may become deposited inside the housing. Impairment of
the protective insulation! Operate the power tool via a residual-
current-operated circuit-breaker (tripping current 30 mA).
Regularly clean the power tool and ventilation slots. Fre-
quency of cleaning is dependent on the material and dura-
tion of use.
Regularly blow out the housing interior and motor with dry
compressed air.
Carbon brushes
The angle grinder features cut-off carbon brushes.
When the wear limit of the cut-off carbon brushes is reached,
the angle grinder switches off automatically.
NOTE
Use only original parts supplied by the manufacturer for replacement
purposes. If non-original parts are used, the guarantee obligations of
the manufacturer will be deemed null and void.
14
Gears
NOTE
Do not loosen the screws on the gear head during the warranty
period. Non-compliance will deem the guarantee obligations of
the manufacturer null and void.
Repairs
Repairs may be carried out by an authorised customer service
centre only.
Spare parts and accessories
For other accessories, in particular grinding tools, see the ma-
nufacturer's catalogues.
Disposal information
WARNING!
Render redundant power tools unusable by removing the po-
wer cord.
EU countries only
Do not throw electric power tools into the household
waste!
In accordance with the European Directive 2012/19/EU
on Waste Electrical and Electronic Equipment and
transposition into national law used electric power tools
must be collected separately and recycled in an env-
ironmentally friendly manner.
NOTE
Please ask your dealer about disposal options!
-Declaration of Conformity
We declare under our sole responsibility that the product des-
cribed under page 5 conforms to the following standards or
normative documents:
EN 60745 in accordance with the regulations of the directi-
ves 2014/30/EU 2006/42/EC, 2011/65/EU.
Responsible for technical documents:
CONEL GmbH
Margot-Kalinke-Straße 9 / 80929 München
01.02.2021
CONEL GmbH
Margot-Kalinke-Straße 9 / 80929 München
Exemption from liability
The manufacturer and his representative are not liable for any
damage and lost profit due to interruption in business caused
by the product or by an unusable product.
The manufacturer and his representative are not liable for any
damage which was caused by improper use of the product or by use
of the product with products from other manufacturers.
WS 12125
Advertenties
Inhoudsopgave
