Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6. Removing the fitting (Scandinavian Oval)
26. Close the cover upwards.
34
27. Slide the cover downwards.
35
9
Cover snaps into place.
28. Press the inlay into place.
36
29. Fit the outside handle.
37
30. Use the grub screws to tighten both handles (TX15).
38
31.
Insert the inside handle cover and, if necessary, the cylinder cover (not
for MO version) on the escutcheons.
39
9
SmartHandle AX Advanced fully installed.
6. Removing the fitting (Scandinavian
Oval)
ü
1.5 mm hexagonal wrench available.
1.
Remove the fitting in the reverse order to installation.
2.
Loosen the cover by bending the inlay outwards using the special tool.
3.
Insert a 1.5 mm hex key into the hole in the spindle mount in the module
support.
40
4.
Bend the hex key to the side where the hole is located while pulling on
the outside handle.
41
9
SmartHandle AX Advanced is now removed.
7. Replacing batteries (Scandinavian
Oval)
NOTE
Malfunctions due to poor contact or different discharge
Contact surfaces that are too small/contaminated or different discharged
batteries can lead to malfunctions.
1.
Only use batteries that are approved by SimonsVoss.
2.
Do not touch the contacts of the new batteries with your hands.
3.
Use clean and grease-free gloves.
4.
Always replace all batteries at the same time.
Special tool at hand.
ü
Gloves at hand.
ü
1.
Insert the special tool into the cover inlay on the electronics side.
42
2.
Use the special tool to carefully bend the cover inlay upwards.
43
3.
Slide the cover upwards.
44
Cover unlocked.
9
4.
Remove the cover.
45
5.
Use the special tool to detach the battery module clip.
46
6.
Remove the battery module.
47
30 / 52
SmartHandle AX Advanced Scandinavian Oval
7.
Use the special tool to detach the battery clip.
48
8.
Remove the upper batteries.
49
9.
Carefully bend the intermediate spring to one side.
10. Remove the lower batteries.
50
11.
Insert two new batteries with the positive terminals next to each other
(type CR2450).
51
9
Intermediate spring visible above the lower batteries.
12.
Insert two new batteries with the positive terminals next to each other
(type CR2450).
52
13.
Reattach the battery clip.
53
14. Put the battery module back into the module support.
54
55
15.
Use the special tool to reattach the battery module clip.
56
9
SmartHandle AX Advanced will beep three times.
16. Position the cover on the fastening plate at the bottom.
57
17.
Fold the cover upwards.
58
18. Push the cover against the door while sliding it downwards at the same
time.
59
Cover snaps into place.
9
19. Press the inlay into place.
60
9
Batteries are now replaced.
8. Technical data
Operating temperature range
Battery type
Battery manufacturer
IP protection rating
Radio emissions
15.24 kHz - 72.03 kHz
Only for item numbers: SV-
S3.*AM.G2*, SV-S3.*A.G2*, SI-
S3.*LN*
13.560006 MHz - 13.560780 MHz
Only for item numbers: SV-
S3.*AM.G2*, SV-S3.*A.G2*, SI-
S3.*M.WO*, SI-S3.*LN*
868.000 MHz - 868.600 MHz /
869.700 MHz - 870.000 MHz
Only for item numbers: SI-
S3.*M.WO*, SI-S3.*LN*
-25 °C to +60 °C
4x CR2450 3V lithium
Murata
Panasonic
Varta
Up to IP66 (WP variant)
10 dBµA/m (3 m distance)
1.04 dBµA/m (3 m distance)
<25 mW ERP
EN
Advertenties
Inhoudsopgave
