Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
7.2 MEMORY STORAGE OF BUS ACCESSORIES
You can add the BUS photocells to the system at any time,
simply by memory-storing them on the board, observing the
following procedure:
1.
Install and program the accessories using the required
address (see paragraph 7.1)
2.
Cut power to the board.
3.
Connect the two accessories cables to the red terminal-
board J10 (any polarity will do).
4.
Power up the board, taking care to first connect the
main power supply (transformer output) and then any
batteries.
5.
Quickly press once only the SW1 (SETUP) push-button, to
execute learning. The BUS LED flashes.
6.
Give an OPEN A impulse, leaves will move and the BUS
learning procedure is over.
The board has memory stored the BUS accessories. Follow the
instructions in the table below to check if the BUS connection
is correct.
Tab. 4 - Description of BUS LED
Normal operation (LED ON even in the
Steady light
absence of photocells)
At least one input engaged: photocell
Slow flashing
engaged or not aligned, Open A or Open
lamp
(flash
B or Stop input engaged
every 0.5 sec)
Light OFF
BUS line short circuited
(flash every 2.5
sec)
If you have detected a BUS connection
error, repeat the acquisition procedure. If
Fast flashing
the error is repeated, make sure that there
lamp
(flash
is not more than one accessory with the
every 0.2 sec)
same address in the system (also see the
accessories instructions)
8 MEMORY STORING THE RADIO CODE
The control board has an integrated 2-channel decoding
system (DS, SLH, LC) named OMNIDEC. This system makes it
possible to memory-store both total opening (OPEN A) and
partial opening OPEN B) of the automated system - this is made
possible by an additional receiver module (fig.3 ref.
radio controls on the same frequency.
The 3 types of radio codes (DS, LSH, LC) cannot
coexist.
Only one radio code can be used at a time.
To change over from one code to another, you
must delete the existing one (see paragraph
on deletion), and repeat the memory-storage
procedure.
8.1 MEMORY STORAGE OF DS RADIO CONTROLS
A maximum of two codes can be stored. One
on the OPEN A channel and one on the OPEN B
channel.
1.
On the DS radio control, select the required ON-OFF
combination for the 12 dip-switches.
2.
Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or partial
opening (OPEN B), and as you hold it down, also press the
SETUP (SW1) push-button. The relevant LED starts to flash
slowly for 5 sec..
3.
Release both push-buttons.
4.
Within these 5 sec., press the appropriate push-button on
the radio control.
5.
The relevant LED lights up on steady beam for 1 second and
then goes OFF, indicating that storage was executed.
6.
To add other radio controls, set the same ON - OFF
combination used in point 1.
8.2 MEMORY STORAGE OF SLH RADIO CONTROLS
) and
A maximum of 250 codes can be memory
stored, split between OPEN A and OPEN B.
1.
On the SLH radio control, simultaneously press and hold
down push-buttons P1 and P2.
2.
The radio control LED begins to flash.
3.
Release both push-buttons.
4.
Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or partial
opening (OPEN B), and as you hold it down, also press the
SETUP (SW1) push-button. The relevant LED starts to flash
slowly for 5 sec.
5.
Release both push-buttons.
6.
Within these 5 sec., while the radio control LED is still flashing,
press and hold down the required push-button on the radio
control (the radio control LED lights up on steady beam).
7.
The LED on the board lights up on steady beam for 1
second and then goes OFF, indicating that storage was
executed.
8.
Release the radio control push-button.
6
Fig. 3
Advertenties
Hoofdstukken
Inhoudsopgave
