Bosch GSH 5 CE Professional Oorspronkelijke Gebruiksaanwijzing pagina 12
Verberg thumbnails
Zie ook voor GSH 5 CE Professional:
- Oorspronkelijke gebruiksaanwijzing (143 pagina's)
Advertenties
Beschikbare talen
Beschikbare talen
12 | English
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ac-
cessories or is poorly maintained, the vibration level and
noise emission value may differ. This may significantly in-
crease the vibration and noise emissions over the total work-
ing period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and accessories, keeping their hands warm, and
organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary handle (see figure A)
Do not operate your power tool without the auxiliary
u
handle (10).
You can swivel the auxiliary handle (10) to any angle for a
safe work posture that minimises fatigue.
– Loosen the knurled nut (11), rotate the auxiliary handle
(10) to the required position and retighten the knurled
nut (11).
Changing the Tool
With the SDS max tool holder, you can change the applica-
tion tool simply and easily without additional aids.
The dust protection cap (1) largely prevents the penetration
of dust into the tool holder during operation. When inserting
the tool, make sure that the dust protection cap (1) does not
become damaged.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
Inserting the application tool (see figure B)
– Clean and lightly grease the shank of the application tool.
– Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling on the tool.
Removing the application tool (see figure C)
– Push the locking sleeve (2) back and remove the applica-
tion tool.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
1 609 92A 9VB | (07.08.2024)
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Operation
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Starting Operation
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool.
Switching On and Off
– To start the power tool, push the on/off switch (6) up-
wards (I) until it locks in place.
– To switch off the power tool, push the on/off switch (6)
back down (0) and release it.
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Adjusting the Speed/Impact Rate
The constant electronic control keeps the preselected speed
and impact rate nearly constant between no-load and load
conditions.
The electronic control enables continuous speed and impact
rate preselection for material-specific adjustments.
Select the speed with the thumbwheel (7) according to the
material.
When inserting the mains plug into the plug socket or after a
power failure, the electronic control automatically sets the
highest speed and impact rate. This ensures that the power
tool works at optimum performance even if the
thumbwheel (7) has been preset too low.
The information in the table below is the recommended val-
ues.
Bosch Power Tools
Advertenties
