Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
SmartHandle AX Advanced Escutcheon installation
40
18. Measure the door thickness.
41
19. Measure the total length of the spindle.
42
20. Locate the inside of the spindle (four-edge end up to the centre of the
first groove = 26 mm).
21.
Use the table to determine the position of the O-ring.
43
Door thickness
Area
(mm)
S
32 – <36
S
32 – <36
S
36 – <41
S
36 – <41
S
41 – <46
S
41 – <46
S
46 – <51
S
51 – 54
M
52 – <56
M
52 – <56
M
56 – <61
M
56 – <61
M
61 – <66
M
61 – <66
M
66 – <71
M
71 – 74
L
72 – <76
L
72 – <76
L
76 – <81
L
76 – <81
L
81 – <86
L
81 – <86
L
86 – <91
L
91 – 94
XL
92 – 184
22. Insert the spindle into the door with the ring-free side as far as it will go.
44
23. Place the inside handle unit on the spindle.
24. Firmly screw the inside handle unit onto the sleeve nuts (PH2).
45
28
29
30
31
25. Place the cover on top of the fastening plate.
50
26. Fold down the cover.
51
EN
Spindle length
Ring position
(mm)
84
3
94
5
84
2
94
4
84
1
94
3
94
2
94
1
104
3
114
5
104
2
114
4
104
1
114
3
114
2
114
1
124
3
134
5
124
2
134
4
124
1
134
3
134
2
134
1
O-ring is 30–35 mm from the cut
end of the spindle.
8. Removing the fitting (full leaf)
27. Push the cover against the door, sliding it upwards at the same time.
52
Cover snaps into place.
9
28. Press the inlay into place.
53
29. Fit the outside handle.
54
30. Use the grub screws to tighten both handles (TX15).
55
31.
Place both rosette covers on their respective rosettes.
56
9
SmartHandle AX Advanced fully installed.
8. Removing the fitting (full leaf)
ü
1.5 mm hexagonal wrench available.
1.
Remove the fitting in the reverse order to installation.
2.
Loosen the cover by bending the inlay outwards using the special tool.
3.
Insert a 1.5 mm hex key into the hole in the spindle mount in the module
support.
57
4.
Bend the hex key to the side where the hole is located while pulling on
the outside handle.
58
SmartHandle AX Advanced is now removed.
9
9. Replacing the batteries
NOTE
Malfunctions due to poor contact or different discharge
Contact surfaces that are too small/contaminated or different discharged
batteries can lead to malfunctions.
1.
Only use batteries that are approved by SimonsVoss.
2.
Do not touch the contacts of the new batteries with your hands.
3.
Use clean and grease-free gloves.
4.
Always replace all batteries at the same time.
Special tool at hand.
ü
ü
Gloves at hand.
1.
Insert the special tool into the cover inlay on the electronics side.
59
2.
Use the special tool to carefully bend the cover inlay upwards.
60
3.
Slide the cover downwards.
61
9
Cover unlocked.
4.
Remove the cover.
62
5.
Use the special tool to detach the battery module clip.
63
6.
Remove the battery module.
64
7.
Use the special tool to detach the battery clip.
65
8.
Remove the upper batteries.
66
9.
Carefully bend the intermediate spring to one side.
35 / 60
Advertenties
Inhoudsopgave
