Download Inhoudsopgave Inhoud Print deze pagina

For Door Thickness X: Preparing The Spindle And Threaded Rods; Installing The Fitting - SimonsVoss SmartHandle AX Korte Handleiding

Advanced escutcheon installation
Inhoudsopgave

Advertenties

Beschikbare talen
  • NL

Beschikbare talen

  • DUTCH, pagina 42
4. Structure
Adapter sleeve, 8.5 mm spindle
Adapter sleeve, 10 mm spindle
4. Structure
1
5. Prepare door (drilling template)
Pin or scriber at hand.
ü
Drill at hand.
ü
Suitable drill bit at hand (Ø 8.5 mm).
ü
ü
Ruler at hand.
ü
PH2 screwdriver at hand.
1.
Remove the mortise lock.
2
2.
Measure the distance (gap between the spindle and cylinder axes of ro-
tation).
3
3.
Fit the mortise lock.
4
4.
Insert the spindle into the mortise lock.
5
5.
Place the drilling template on the spindle.
6
6.
Align the drill template vertically using the printed scale.
7.
Mark the points to be drilled on the door.
7
8.
Remove the drilling template and spindle.
8
9.
Remove the mortise lock.
9
10. Drill the required holes.
10
11.
Fit the mortise lock.
11
6. For door thickness X: Preparing the
spindle and threaded rods
ü
Caliper gauge at hand.
ü
Saw at hand.
ü
PH2 screwdriver at hand.
1.
Measure the door thickness.
12
2.
For door thickness X: screw the 10 mm screws, threaded sleeves and
threaded rods together.
13
3.
For X: mark the sawing points on the threaded rods and spindle.
14
15
4.
For X: Use a suitable saw to cut the threaded rods and spindle.
16

7. Installing the fitting

ü
Door pre-drilled.
ü
PH2 screwdriver at hand.
ü
TX15 screwdriver at hand.
ü
Caliper gauge at hand.
34 / 60
SmartHandle AX Advanced Escutcheon installation
1.
For non-MO: insert the blank cylinder.
NOTE
Feed the blank cylinder into the hole using a screwdriver
It is difficult to position the blank cylinder correctly, especially in thick doors.
1.
Insert a screwdriver into the hole in the blank cylinder.
2.
Position the blank cylinder using the screwdriver.
17
18
2.
For non-MO: screw the blank cylinder firmly into position.
19
3.
Insert the sleeve nuts into the fastening plate.
20
4.
For 7 mm spindle: Insert the adapter shoe into the spindle mount on the
module support.
21
5.
Insert the module support into the fastening plate.
22
6.
Slide the module support upwards.
23
9
Module support snaps into place.
7.
Fasten the module support to the fastening plate (PH2) with the 12 mm
screws.
24
25
8.
Place the compshells on the sleeve nuts.
26
9.
Insert the module support with the fastening plate into the outer side of
the door.
27
10. Firmly fasten the cylinder escutcheon to the sleeve nuts (PH2).
28
29
30
31
32
11.
For 7 mm spindle: Place the adapter sleeve in the inside handle in such a
way that the recess faces the grub screw.
33
12.
Determine the required direction of rotation for your inside handle.
13.
Place the interchangeable plate into your inside handle escutcheon as
required.
34
35
14. Pre-tension the spring element on the interchangeable plate.
36
15.
Slide the spring element nose into the slot in the escutcheon.
37
16. Attach the end of the spring element into the slot in the escutcheon.
38
17.
For 8.5 mm and 10 mm spindle: slide the adapter sleeve into the centre
of the spindle. Use a punch and hammer to make an indent in the ad-
apter sleeve to prevent it from slipping.
39
EN

Advertenties

Inhoudsopgave
loading

Inhoudsopgave