Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Propane G31
Town
G110
Semi-
Natural G20
Rapid
Butane G30
Propane G31
Town
G110
Natural G20
Rapid
Butane G30
Propane G31
Town
G110
Dual
Natural G20
burner
Butane G30
inner
Propane G31
Town
G110
Dual
Natural G20
burner
Butane G30
outer
Propane G31
CAUTION: save the orifices removed from the appliance for future use
Regulation of burners
Regulation of the "MINIMUM" on the burners
To regulate the minimum on the burners carry out the following procedure indicated below:
1) Turn on the burner and put the knob onto position MINIMUM ( small flame ).
2) Remove the knob ( Fig. 10) of the tap which is set for standard pressure. The knob is found on the bar of
the tap itself.
3) Beside the tap bar on the work top, use a small screwdriver that fits the screw (gold) found on the lower
part of the tap and turn the fixing screw to the right or left until the flame of the burner is regulated in the most
suitable way to MINIMUM.
4) Make sure that that the flame does not go out when changing the position quickly from MAXIMUM to the
MINIMUM position.
ATTENTION: The regulation described above can be carried out only with burners using natural gas,
while with burners using propane gas the screw must be fully screwed in, in a clockwise direction.
Descriptions
DESCRIPTIVE CAPTION FOR HOB
1. Dual burner
2. Rapid burner
3. Medium burner
4. Small Burner
5. Dual in burner control knob
6. Dual out burner control knob
7. Rapid burner control knob
8. Medium burner control knob
9. Small burner control knob
Service & maintenance instructions
Service and maintenance only to be carried out by an authorised person
To replace parts such as burners, valves and electric components, the hotplate must be removed from the
bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing
the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotplate top and
finally replacing the defective parts.
Note: if the valves must be replaced, first disassemble the ignitions switches wires.
It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal
between the body and the gas train.
WARNING: Disconnect power before servicing unit.
For the location of the wall receptable for the connection of the three-pin earthed plug of the
appliance, see indications given in Fig. 1- 2
37
50
71
8
192
-
20
101
-
28
66
127
37
66
125
8
280
-
20
129
-
28
87
218
37
87
214
8
130
-
20
70
-
28
46
211
37
46
207
8
2x300
-
20
2x110
-
28
2x69
298
37
2x69
293
-
1,00
860
397
1,75
1505
167
1,75
1505
-
1,75
1505
-
1,75
1505
681
3
2580
286
3
2580
-
3
2580
-
3
2580
181
0,8
688
76
0,8
688
-
0,8
688
-
0,8
688
885
4,4
3784
419
4,4
3784
-
4,1
3526
-
4,1
3526
DESCRIPTION OF HOBS
Model 'A' Fig. 11
Model 'B' Fig. 12
0,30
258
0,44
378
31 reg
0,44
378
31 reg
0,44
378
0,44
378
0,75
645
42 reg
0,75
645
42 reg
0,75
645
0,75
645
0,30
258
27 reg
0,30
258
27 reg
0,30
258
0,30
258
1.8
1548
65 reg
1.8
1548
65 reg
1.8
1548
1.8
1548
27
31
31
42
42
27
27
65
65
Advertenties
Inhoudsopgave
