Download Inhoudsopgave Inhoud
Deel
Print deze pagina
  1. Handleidingen
  2. Merken
  3. Chamberlain Handleidingen
  4. Deuropeningssystemen
  5. LiftMaster SCS200
  6. Handleiding

Installation Checklist - Preparations - Chamberlain LiftMaster SCS200 Handleiding

Verberg thumbnails
Inhoudsopgave

Advertenties

Beschikbare talen

Beschikbare talen

PLEASE START BY READING THESE IMPORTANT SAFETY RULES • SAVE THESE INSTRUCTIONS
This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal injury or
damage to property. Please read these warnings carefully.
This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and operated in
strict accordance with the following safety rules.
Incorrect installation and/or failure to comply with the following instructions may result in serious personal injury or property
damage.
When using tools and small parts to install or carry
out repair work on a gate exercise caution and do not
wear rings, watches or loose clothing.
Installation and wiring must be in compliance with
your local building and electrical installation codes.
Power cables must only be connected to a properly
earthed supply.
Any entrapment possibility by the moving wing
between wing & walls must be secured with safety
edges or IR-sensors.
Please remove any locks fitted to the gate in order to
prevent damage to the gate.
After the installation a final test of the full function of
the system and the full function of the safety devices
must be done.
This drive cannot be used with a gate incorporating a
wicket door unless the drive cannot be operated with
the wicket door open.
CARTON CONTENTS SCS 200
Drive motors
Box for control
Cover for box
Hinges for box
Control
Transformer
Baseplate For Transformer
Remote control
Radio receiver
Radio module
Hardwarebag For Box
Pillar fittings
Gate fittings
Hardwarebag
Instructions
Flashing light
Key switch
Photocells
* depending on model resp. available as optional accessory

INSTALLATION CHECKLIST - PREPARATIONS

Check the carton contents and read the instructions carefully. Make sure your gate equipment operates perfectly. The gate must run evenly and
smoothly and must not stick at any point. Remember that the ground level may be several centimeters higher in winter. The gate must be stable
and as free of backlash in order to prevent any unwanted movement. The easier the gate movement the less power is needed by the motor.
Write down any materials you still need and obtain them before starting to install. Heavy-duty plugs, bolts, gate stops, cables, distribution boxes,
tools, etc.
WARNING / ATTENTION
IMPORTANT FITTING AND OPERATING INSTRUCTIONS
2x*
1x
1x
4x
1x
1x
1x
1-2x*
1
1x
1x
2x*
2x*
1x
1x
1x*
1x*
1x*
Frequently examine the installation for imbalance and
signs of wear or damage to cables, hardware and
mountings. Do not use if repair or adjustment is
necessary. Gates which stick or jam must be repaired
immediately. Employ a qualified technician to repair the
gate, never attempt to repair it yourself.
Keep additional accessories away from children. Do not
allow children to play with pushbuttons or remote controls.
A gate can cause serious injuries as it closes.
Disconnect electric power to the system before making
repairs or removing covers.
A disconnecting device must be provided in the
permanently-wired installation to guarantee all-pole
disconnection by means of a switch (at least 3mm
contact gap) or by a separate fuse.
Make sure that people who install, maintain or operate
the gate drive and/or the control board are qualified and
follow these instructions.
Keep these instructions in a safe place so that you can
refer to them quickly when you need to.
The full protection against potential squeeze or
entrapment must work direct when the drive arms are
installed.

Advertenties

Inhoudsopgave
loading

Gerelateerde Handleidingen voor Chamberlain LiftMaster SCS200

Gerelateerde Producten voor Chamberlain LiftMaster SCS200

Inhoudsopgave