Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENGLISH
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don't cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
CREATING A CENTERPIECE EFFECT
Whit the optional CPB-4 "Centerpiece bracket" you can make a fantastic combination of 4pcs ORION led.
The result is a superb LED Centerpiece effect, really a must if you want an original and eye-catching effect!
JB SYSTEMS
®
OPERATION MANUAL
3/58
ENGLISH
DESCRIPTION:
1. Mains input with IEC socket, connect the supplied mains cable here
2. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the
mains input of the next Orion for easier linking.
3. Fuse holder
4. DMX input
5. DMX output
6. ¼" Jack input for the optional CA-8 hand controller
7. Sensitivity control for the internal microphone
8. Internal microphone
9. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
10. Slave LED: is lit when the unit is in slave mode
11. Sound LED: blinks to the rhythm of the music while the unit is in audio mode
12. DMX LED: is lit when the unit receives a DMX-signal
13. Master LED: is lit when the unit is switched as master
14. MENU button: used to select the different menu items
15. DOWN button: to go back in the menu and to lower the values shown on the display.
16. UP button: to go up in the menu and to increase the values shown on the display.
17. ENTER button: used to confirm your choice.
18. DISPLAY shows the various menus and the selected functions.
HOW TO SETUP:
MAIN MENU:
To select any of the menu options, press the MENU button up to when the required one is shown on the
display.
Select the function with the ENTER button. The display will blink.
Use DOWN and UP button to choose the desired menu option.
Once the required menu option is selected, press the ENTER button to select. To go back to the functions
without any change press the MENU button or just wait 8 seconds. The menu structure is shown below.
Used to set the starting address in a DMX setup.
Press the MENU button until
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to change the DMX512 address.
Once the correct address shows on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
ORION
JB SYSTEMS
DMX512 Address Setting
is shown on the display.
4/58
®
OPERATION MANUAL
ORION
Advertenties
Inhoudsopgave
