Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Precautions
Do not place your cabinet in an area likely to be flooded.
•
Do not position your cabinet near to a source of heat or expose it to
•
the effects of direct sunlight.
Prevent water from splashing on the entire rear section of the appliance.
•
Position your appliance so that there is a minimum space of 5 – 10 cm
•
between the wall and the rear wall of your cabinet.
If you are positioning your cabinet under a work surface, leave a
•
minimum space of 5 cm all around the appliance including under the
work surface.
Allow for a ventilation grill on the work surface
(recommended).
Arrange the power lead so that it is accessible and does not come
•
into contact with any component of the appliance.
Fitting the handle (Full Glass door only on models 5059V3-S, 5059V3-V, 5259V3-S, 5259V3-V)
•
Unscrew the three screws placed on the side of the door, using the Allen
wrench, which you will find in the handle's box.
•
Position the handle on the specially designed groove on the door frame
(figure 2).
•
Insert the handle all the way into the groove using a forward movement
(figure 2).
•
Screw the three screws back on (figure 3).
•
Take care not to catch the seal when screwing.
Note: adjustment of the handle is possible thanks to the oblong holes.
Install the stop (which is located in the accessories bag) at the back of the
cabinet (on models 5259V3-S, 5259V3-V) / see diagram).
•
This allows a space of 7 cm to be maintained between the wall and the
rear of the cabinet. This space allows your cabinet's power consumption
to be optimised.
•
Place the 2 caps in the 2 holes at the top of the cabinet.
Wall fixing of the cabinet
For large models, if the wine cabinet is not being built in, it is essential
to secure it to the wall to prevent it from tipping forward. You will find
all the necessary parts in the accessories bag supplied with the unit. For
installation (see diagram below):
1
A
Loosen the screws
.
2
B
Attach the bracket
3
C
Clip the nut
to this bracket
to the cabinet).
Warning: make sure that the part is correctly clipped by
pulling upwards by hand. The clip must not come out.
4
Preposition the wall bracket
8
GB
for drilling the holes for the wall-mounting screws,
4/ INSTALLING YOUR WINE CABINET
A
to the cabinet with the screws
B
(preferably choose the hole nearest
D
(on the nut to determine the position
Slightly tilt the cabinet backwards to adjust the front feet (adjusted by
•
screwing or unscrewing), so that you can level your cabinet (use of a
spirit level is recommended).
Install the carbon filter, which you will find inside your cabinet's
•
"accessories" packet, by placing it in the air circulation hole located
inside the cabinet on the top left hand side (see diagram below).
Never obstruct the front ventilation grid.
•
Beware: any changing of the control panel LED should only be
carried out by a qualified electrician.
Handle
Front
•
Do not push the caps all the way in,
in order to allow the rear stop to be
installed.
•
Slide the rear stop between the caps
and the wall of the cabinet, then push
the 2 caps all the way in.
5
Drill the holes then attach the wall
bracket
Warning: ensure that the wall fixing can withstand a tensile
force of 100 kg.
.
6
Tighten screw
there is contact between the wall bracket
Only full tightening of the screw will ensure correct fixing of the unit.
Repeat the installation on the other side of the cabinet.
View from above
Figure 1
Figure 2
E
D
with suitable screws
.
G
F
with the washer
until it is screwed fully in and
Seal
Door frame
Figure 3
D
C
and the nut
.
Advertenties
Hoofdstukken
Inhoudsopgave
