Pagina 1
SAEY PEAK – PEAK S – PEAK S HIGH – B – W NL - Installatie- en gebruiksaanwijzing FR - Notice d’installation et d’utilisation EN - Installation and user manual...
NLEIDING Hartelijk gefeliciteerd ! Wij danken u van harte voor de keuze van een Saey kachel. Met de Saey Peak, Peak S of Peak S High kiest u resoluut voor een technische en esthetisch modern ogende houtkachel. Naast het design, hechten wij groot belang aan een geavanceerde verbrandingstechniek en hoogwaardige kwaliteit.
ECHNISCHE GEGEVENS Saey Peak Kenmerk Eenheid Saey Peak Co-uitstoot ( bij 13% O2 ) Mg/Nm³ 1250 Uitstoot fijn stof (bij 13% O Mg/Nm³ Rendement Nominaal vermogen Rookgastemperatuur °C Schouwtrek bij nominaal vermogen Schouwtrek limieten 12 – 20 Toevoer verse lucht m³/h...
Pagina 17
Saey Peak S Kenmerk Eenheid Saey Peak S Co-uitstoot (bij 13% O Mg/Nm³ 1125 Uitstoot fijn stof (bij 13% O Mg/Nm³ Rendement Nominaal vermogen Rookgastemperatuur °C Schouwtrek bij nominaal vermogen Schouwtrek limieten 12 – 20 Toevoer verse lucht m³/h Brandstof...
Pagina 18
Saey Peak S High Kenmerk Eenheid Saey Peak S High Co-uitstoot (bij 13% O Mg/Nm³ 1125 Uitstoot fijn stof (bij 13% O Mg/Nm³ Rendement Nominaal vermogen Rookgastemperatuur °C Schouwtrek bij nominaal vermogen Schouwtrek limieten 12 – 20 Toevoer verse lucht m³/h...
Deze kachel is niet geschikt om te installeren op een rookkanaal waarop meerdere kachels zijn aangesloten. De Saey Peak, Peak S en Peak S High zijn enkel geschikt om brandhout en houtbriketten in te branden en enkel bestemd voor gesloten werking.
(ventilatie, dampkap, … ) 4.4 Gevaar door gebruik van onaangepaste brandstof De Saey Peak is enkel geschikt om brandhout of houtbriketten in te verbranden. Verder informatie rond het gebruik van de voorgeschreven brandstof vindt u onder hoofdstuk 5.
NSTALLATIEVOORSCHRIFTEN Alle plaatselijke richtlijnen, inclusief de richtlijnen die betrekking hebben op nationale en Europese normen, moeten in acht genomen worden bij de installatie van de kachel. Alleen een toestel dat aangesloten werd door een installateur, garandeert de naleving van de richtlijnen inzake bouwkunde en brandpreventie.
De diameter van de afvoerbuis moet overeenkomen met de diameter 150mm (Peak) of 125mm (Peak S en Peak S High) van de pijpmond van de kachel. In verband met de diameter van de afvoerbuis moet u ook met het volgende rekening houden: De diameter van de afvoerbuis mag niet verkleind worden.
Pagina 23
4) Vervolgens de achterwand / hitteschild opnieuw monteren Afbeelding 4.3 Achterwand opnieuw monteren Montage van het aansluitstuk bij boven aansluiting 1) Achterwand / hitteschild demonteren – 2 kruisschroeven M6 x 8 mm Afbeelding 4.4 Achterwand demonteren...
Pagina 24
2) Demonteer het afdekplaatje aan de bovenkant. Grijp door de opening in de achterwand en vijs de zeskantschroeven M6 x 16 langs onder los. Afbeelding 4.5 Afdekplaatje bovenaan demonteren 3) Het afdekplaatje uit de vorige stap, monteren aan de rugzijde en deze met behulp van de zeskantschroeven en rondellen terug vastmaken Afbeelding 4.6 Afdekplaatje monteren aan de rugzijde 4) Vervolgens het aansluitstuk op de rugzijde...
De aslade, blokkenhouder en asrooster zijn geplaatst. Controleer de juiste positie van de aslade, het asrooster en de blokkenhouder (op de Peak S) voordat u de kachel voor het eerst gebruikt. De metalen roosterafdekking moet bij de Peak S onder het asrooster worden geplaatst. De luchtopeningen in de roosterafdekking moeten aan de achterkant zitten.
Pagina 26
Klassieke systeem Wanneer de lucht voor de verbranding uit de ruimte wordt aangevoerd waarin de kachel staat opgesteld, dan moet deze voldoende geventileerd worden. Indien er onvoldoende luchttoevoer is, dan kan dit resulteren in een onvolledige verbranding en terugslag van rookgassen. Extra lucht kan aangevoerd worden door vlakbij de kachel een ventilatorrooster te plaatsen naar buiten ( min.
Gebruik enkel schoon, onbehandeld, natuurlijk, gekliefd en droog brandhout of houtbriketten in de voorgeschreven grootte, lengte en hoeveelheid. In de Saey Peak, Peak S en Peak S High zijn enkel brandhout en houtbriketten toegelaten. Peak Optimale brandstofeigenschappen voor de Saey Peak:...
Pagina 28
Optimale omgang met brandhout en houtbriketten Enkel droog hout brandt efficiënt en met lage uitstoot. Optimaal brandhout is daarom: Natuurlijk: Geen gelakt of geïmpregneerd hout e.d. geen gelijmd hout, noch multiplex en geperst hout, wat schors kan bevatten. Alle kunststoffen en chemische bestanddelen kunnen bij het verbranden zeer giftig zijn en schade berokkenen aan de omgeving, maar ook bepaalde onderdelen van uw kachel, alsook de schoorsteen vervuilen of beschadigen.
3) Vuldeur (altijd rechts en enkel bij Peak) 4) Sluiting vuldeur (enkel bij Peak) De kacheldeur en vuldeur zijn bij levering altijd gesloten. Bij de Peak wordt een bedieningshendel geleverd zodat u de sloten makkelijk kan openen en sluiten. Let erop dat bij inwerkingstelling de sloten van beide deuren steeds goed gesloten zijn.
De luchtregeling gebeurt met de bediening die zich aan de voorzijde van de kachel bevindt, in het midden onderaan de kachelruit. Deze bediening zorgt ervoor dat u zelf de hoeveelheid lucht kan regelen die de kachel nodig heeft om te zorgen voor de verbranding.
Pagina 31
Verderbranden Hoe verder we gaan in de verbranding hoe meer de regeling van de verbrandingslucht naar links zal staan. Wanneer we hout willen bijvullen, plaatsen we de verbrandingslucht weer helemaal open naar rechts. U mag hout bijvullen via de vuldeur, maar zorg ervoor dat er in het vlammenbeeld zo goed als geen vlammen meer zichtbaar zijn.
Reinigen van kachelruit De Saey Peak, Peak S en Peak S High beschikken over een zelfreinigend systeem, waarbij vervuiling van de kachelruit zo lang mogelijk uitgesteld wordt. Toch kunnen verschillende oorzaken (vochtig hout, slecht stoken, … ) niet vermijden dat de kachelruit sneller vuil wordt.
Roestelementen verwijderen Het rooster kan aan de voorkant van de Peak S verwijderd worden om de verbrandingskamer te reinigen. Het rooster kan gemakkelijk verwijderd worden om het as compartiment schoon te maken. Hiervoor is aan de voorkant van het rooster een handvat gegoten.
TORINGEN OORZAKEN EN OPLOSSINGEN Storing Oorzaak Oplossing Vuur brandt slecht of raam Hout te vochtig Droog hout gebruiken wordt snel vuil vochtigheidsgraad max. 20% Verkeerde brandstof Alleen geschikt hout gebruiken Juiste hoeveelheid hout respecteren Schoorsteentrek te zwak Dichtheid van de afvoer controleren (min 12 Pa ) Niet gesloten reinigingsopeningen van schoorsteen...
ARANTIE Uw Saey kachel geniet een garantie van 2 jaar op alle productiefouten en dit vanaf de datum van aankoop en in die mate dat het gebruik in overeenstemming is met de installatievoorschriften en gebruiksaanwijzingen. Uw kasticket of de factuur met vermelding van de datum van aankoop is uw garantiebewijs.
NTRODUCTION Félicitation ! Nous vous remercions de votre choix pour le poêle à bois Saey. Avec le Saey Peak, Peak S ou Peak S High, vous faites le choix décisif d'un poêle à bois technique et esthétiquement moderne. Outre le design, nous attachons une grande importance pour une technologie de combustion à la pointe et de haute qualité.
ARACTÉRISTIQUES TECHNIQUE Saey Peak Caractéristique Unité Saey Peak Émission de Co (à 13% O2) Mg/Nm³ 1250 Émission de fine poussière (à 13% O2) Mg/Nm³ Rendement Puissance nominal Température fumées °C Tirage cheminée à puissance nominal Limites tirage cheminée 12 – 20 Arrivé...
Pagina 38
Saey Peak S Caractéristique Unité Saey Peak S Émission de Co (à 13% O2) Mg/Nm³ 1125 Émission de fine poussière (à 13% O2) Mg/Nm³ Rendement Puissance nominal Température fumées °C Tirage cheminée à puissance nominal Limites tirage cheminée 12 – 20 Arrivé...
Pagina 39
Saey Peak S High Caractéristique Unité Saey Peak S High Émission de Co (à 13% O2) Mg/Nm³ 1125 Émission de fine poussière (à 13% O2) Mg/Nm³ Rendement Puissance nominal Température fumées °C Tirage cheminée à puissance nominal Limites tirage cheminée 12 –...
Ce poêle ne peut-être raccordé à un conduit de fumées auquel sont raccordés plusieurs poêles. Le Saey Peak, Peak S et Peak S High sont uniquement approprié à brûler des bûches et briquettes de bois et seulement pour fonctionnement portes fermée.
4.4 Risques dû à l’utilisation de carburant inapproprié Le Saey Peak est uniquement approprié pour brûler des bûches ou briquettes de bois. Plus d’information sur l’utilisation du combustible approprié, voir chapitre 5. 4.5 Risques dû à la fermeture du clapet d’air L’alimentation en air de combustion doit être complètement fermée, tant qu’il y a encore une flamme jaune...
’ ONSIGNES D INSTALLATION Toutes les réglementations locales, y compris les lignes directives, concernant les normes nationales et européennes, doivent être respectées lors de l’installation du poêle. Seul un appareil raccordé par un installateur garantit la soumission des directives de la construction et prévention d’incendies.
Pagina 43
Raccordement du poêle à la cheminée Le Saey Peak dispose d’une sotie arrière et poêle peut être raccordé directement à la cheminée. Il est important que ces pièces soient étanches. Le diamètre du conduit d’évacuation doit correspondre au diamètre 150 mm (Peak) ou 125mm (Peak S/Peak S High) du buselot du poêle.
Pagina 44
3) Viser la pièce de raccordement à l’arrière – avec 2 x vis à tête hexagonale M6 x 20, 2x hex M6, 4x rondel U18, SW 10 mm Figure 4.2 viser la pièce de raccordement à l’arrière 4) Montez par la suite le panneau arrière / bouclier thermique Figure 4.3 A nouveau monter le panneau arrière Montage de la pièce de raccordement pour sortie dessus...
Pagina 45
2) Démontez le bouche trou sur le dessus. Dévissez par l’ouverture dans l’arrière la vis à tête hexagonale M6 x 16. Figure 4.5 Démonter le bouche trou sur le dessus 3) Le bouche trou de l’étape précédente, montez celle-ci à l’aide des vis à tête hexagonal et rondelle Figure 4.6 Monter le bouche trou à...
Le tiroir à cendres, le porte-blocs et la grille à cendres sont en place. Vérifiez la position correcte du tiroir à cendres, de la grille à cendres et du porte-blocs (sur le Peak S) avant d'utiliser le poêle pour la première fois.
Pagina 47
Système avec arrivé d’air externe Dans certains cas il est conseillé de prendre l’air de combustion depuis l’extérieur. Pour cela, un tuyau de Ø 80 (flexible ou conduit) est directement raccordé à l’arrière du poêle. Ce tuyau doit être protégé de la condensation en l’isolant aux endroits où ils sont encore soumis à l’air chaud.
Utilisez seulement du bois propre, non traité, naturel, fendu et séché (2 ans min.) ou des briquettes de bois de longueur, taille et quantité prescrite. Dans le Saey Peak, Peak S et Peak S High des bûches et des briquettes de bois sont autorisées. Peak Caractéristiques de combustible optimal pour le Saey Peak:...
Pagina 49
Résultat optimal avec bûches ou briquettes de bois Seul le bois sec brûle efficacement avec de faibles émissions. Du bois optimale est donc: Naturel : Pas de bois peint ou traité etc. Pas de bois collé, contreplaqué, pressé qui peut contenir de l’écorce. Brûler du plastique ou produits chimiques est strictement interdit, ils peuvent être toxique et nuire à...
Pagina 50
La porte du poêle et la porte de remplissage sont toujours fermées à la livraison. Le levier est aussi livré avec le Peak pour ainsi ouvrir et fermer plus facilement. Faites attention ; lors du fonctionnement les serrures des deux portes soient toujours fermées.
Pagina 51
Le réglage de l’air ce manipule grâce au clapet d’air qui se trouve à l’avant du poêle, en bas au centre de la vitre. Ce clapet d’air vous permet de régler la quantité d’air que le poêle a besoin pour assurer une belle combustion.
Combustion Au plus vous avancez dans la combustion, au plus le réglage de l’air de combustion se mets vers la gauche. Quand vous remplissez de bois, mettez le réglage de l’air de combustion à nouveau complètement ouvert vers la droite. Vous pouvez remplir de bois par la porte de remplissage, mais assurez-vous qu’il n’y a plus de grandes flammes.
Démontage du support de bloc (Peak S) et de la grille d'essieu (Peak et Peak S) Lors de l'installation de la grille à cendres dans le Peak S, le couvercle de la grille en tôle d'acier doit être placé sous la grille à cendres. Les orifices d'aération du couvercle de la grille doivent être placés à l'arrière.
ANNES CAUSES ET SOLUTIONS Pannes Causes Solutions Mauvaise combustion Bois trop humide Utiliser du bois sec: taux d’humidité vitre vite sale max. 20% Mauvais combustible Utilisez le bon combustible. Respectez la bonne quantité Tirage de cheminée trop faible Contrôlez l’étanchéité de la sortie. (min 12 Pa) Fermée les trappes de visite de la cheminée qui sont ouverte.
Les demandes de garantie doivent toujours être faites via votre point de vente. UMÉRO DE SÉRIE Vous trouvez le numéro de série sur la plaque d'identification à l’arrière de votre poêle à bois Saey Peak, Peak S ou Peak S High. Indispensable pour toute demande d’intervention sous garantie.
Peak S High have been built with the most modern technology available and meets the European DIN EN 13240. The Peak S High uses the same technology and combustion chamber as the Peak S, but has a higher base. On top of that Saey guarantees full service, even long after your purchase! An undisputable efficiency and years of cozy heating times are the responsibility of our certified partners and Unifire.
Saey Peak S Characteristic Unity Saey Peak S Carbon emission ( at 13% O2 ) Mg/Nm³ 1125 Emission dust particles ( at 13% O2 ) Mg/Nm³ Efficiency Nominal power Flue gas temperature °C Draft at nominal consumption Draft limits 12 – 20 Fresh air supply m³/h...
Pagina 59
Saey Peak S High Characteristic Unity Saey Peak S High Carbon emission ( at 13% O2 ) Mg/Nm³ 1125 Emission dust particles ( at 13% O2 ) Mg/Nm³ Efficiency Nominal power Flue gas temperature °C Draft at nominal consumption Draft limits 12 –...
This stove is not equipped to be connected with other ones on the same conduct De Saey Peak, Peak S and Peak S High are solely made to burn wood and briquettes and only to work in a closed environment.
4.4 Risks of using inappropriate fuel The Saey Peak was made solely to burn wood and briquettes. More information on using the right fuel can be find in chapter 5 4.5 Risks of shutting down the air supply As long as the flames look yellow / orange the fresh air supply may never be disconnected.
The diameter of the exhaust pipes must correspond to the 150 mm (Peak) and 125mm (Peak S and Peak S High) exit diameter of the stove. Regarding this diameter should also consider : That it may never diminish and that it fits the chimney in a perfect manner.
Installing the stove adapter when choosing rear connection 1) Back wall / heat shield must be taken off – 2 screws M6 x 8 mm 2) Remove the small round cover in the back wall Fig. 4.1 Remove the back wall 3) Screw the stove adapter on the backside with 2 hexagonal screws M6 x 20, 2 hexagonal nut M6,...
Installing the stove adapter when choosing top connection 1) Back wall / heat shield must be taken off – 2 screws M6 x 8 mm Fig 4.4 take off the back wall 2) Remove the small round cover on the top. Go through the opening at the back side and screw off the hex bolts.
Pagina 65
(on the Peak S) before using the stove for the first time. On the Peak S, the metal grate cover must be placed under the ash grate. The vents in the grate cover should be at the back. This allows better channeling of the central air.
Pagina 66
Combustion air supply In order to have a perfect combustion, sufficient fresh air must be supplied. The required oxygen arrives from the back and in best ways out of the premises. HINT : Bear in mind that the presence of other stoves or venting installations in the same room(s) will have disruptive effect on the functioning of your stove.
Only use wood of clean, untreated, natural, chopped and dry wood or briquettes in the prescribed length and quantity The Saey Peak, Peak S and Peak S High allows to burn wood and briquettes. Peak Ideal features for the Saey Peak:...
Stay close to your stove in the first hours that it is burning and remove any signs of moisture before it can burn in the paint. Never touch the stove with your bare hands. 6.3 General use 1) Door 2) Door handle 3) Filling door ( always right side, only Peak ) 4) Clinch filling door (only Peak)
Pagina 69
The door of the stove, as well as the filling door are always closed at the delivery. In the delivery of the Peak we had inserted control handle which allows you to open and close the locks in an easy way.
Continuing to burn To refill the stove with wood, please re-open the air control lever to the right. You may refill wood through the filling door on the side, as long as there are no more flames visible. Always open the door in a gentle manner.
Removing the grate elements The grate can be removed from the front of the Peak S to clean the combustion chamber. The grate can be easily removed to clean the ash compartment. A handle is moulded on the front of the grate for this purpose.
ROUBLESHOOTING Storing Oorzaak Oplossing The fires burns really bad The wood is too wet wood Humidity max. 20% Wrong fuel Only suitable wood Respect the right quantity of wood Chimney draught is too weak Check the density of the exhaust pipe (min 12 Pa) Clean the chimney Too little combustion air...
Warranty requests need to be made via your point of sale. ERIAL NUMBER The serial number can be found on the name tag at the bag of your Saey Peak, Peak S or Peak S High.
Pagina 74
Gelieve bij problemen in onderhoud of werking uw installateur te contacteren Veuillez contacter votre installateur en cas de problèmes d'entretien ou de fonctionnement Please contact your installer in case of maintenance or operation problems Industriepark De Bruwaan 17 9700 Oudenaarde Belgium www.belgofire.be Versie 06 2024...