Inhoudsopgave
Advertenties
Assemble diagonal bars (7312) on both sides
(4a.5). At the sill loosely attach using bolt
(7050). (7050) will be removed during glazing
(section 7b).
Using bolts (7399) and nuts (7053), connect
end bars (7319) and (7320) to corner bars
(7310) ensuring they are pushed against the
eave angle bar (4a.6) (4a.7).
Loosely prepare bolts (7399) and nuts (7053)
in sill bars (7304 / 7306) as shown in (4a.3).
Lower corner bars (7437 / 7438), fitting the
bolt heads of (7052) into the bolt channels of
(7437 / 7438) (4a.4).
Assemble front bar (7444 / 7446) into the
recess in corner bars (7337 / 7438) using bolts
(7399) and nuts (7053) (4a.8) (4a.9).
Assemble ridge bar (7434 / 7436) onto the
ends of corner bars (7437 / 7438) (4a.10)
(4a.11)
Assemble diagonal bars (7312) in the front. At
the sill loosely attach using bolt (7050). (7050)
will be removed during glazing (section 7b).
Position the assembled frame onto the prepa-
red foundation.
Check that the house is level and drill ø6
holes through the prepared holes in (7304)
and (7306).
Insert wall plugs (7421) into the holes and
connect loosely to the foundation using screws
(7411) (4a.12).
4b. RooF
Loosely connect middle bars (7311) between
sill (7304 / 7306) and horizontal bar (7444 /
7446) (4b.1) (4b.2).
Loosely connect middle bars (7439) between
ridge (7434 / 7436) and horizontal bar (7444 /
7446) (4b.2).
Assemble roof corner bars (7432) (7433) onto
the eave angle (4b.3) (4b.4). Ensure that the
roof corner bars sit correctly on the assembly
edge on the eave angle (4b.9) and that the
small holes on the outside of (7432 / 7433) are
at the eave end (4b.3).
Connect the roof corner bars (7432) (7433) to
the ridge (7434 / 7436) and to the front corner
bars (7437 / 7438) using plate (7348) (4b.6).
Assemble side middle bars (7346) and (7347)
between horizontal bars (7319 / 7320) and
the roof corner bars (7432 / 7433) using plate
(7348) (4b.5).
Insert bolts (7052) into the bolt channels in
roof middle bars (7426) at the eave and lower
onto the eave angle (7314 / 7316) using
washer seal (7395) and nut (7053) (4b.7)
(4b.8). Ensure that (7426) sit correctly on the
assembly edge on the eave angle (4b.9) and
that the small hole on the outside of (7426) is
070.01.1608
at the eave end.
Insert (7052) into the bolt channel in (7426) at
the ridge and connect onto ridge (7434 / 7436)
(4b.10) .
Adjust the frame until it is completely right an-
gular and tighten all screws (7411) and (7412)
and nuts (7053). Please do not over tighten.
Assemble corner braces (7331) between each
side middle bar (7311) and roof middle bar
(7426) by inserting cropped head bolts (7399)
into the bolt channels (4b.11) (4b.12).
5a. SIde wINdow
Connect window bottom bar (7451) to side
bars (7453) and (7454) (5a.2) (5a.3).
Slide pane D into the glazing channels (5a.5)
in the assembled parts (5a.4) (5a.5).
Loosely prepare (7052) and (7053) in window
top bar (7450) and slide onto (7453) and
(7454) fitting the bolt heads of (7052) into the
bolt channels and the glazing into the glazing
channels (5a.6) (5a.7).
Note - If you have chosen 4mm glass glazing,
cut glazing seal (7420) to fit and press into the
space in the glazing channels on the inside of
the window to fix the glass in place (5a.8)
(5a.9).
Check that the side window is right angular
before tightening all bolts.
Please do not over tighten.
Insert brush seal (7457) using one continuous
length into the guides in the top and side bars
(7454) (7450) (7453) (5a.10) and cut to length.
Note - If the brush seal (7457) protrudes along
the top edge of (7450) when the window is
closed, (see section 8a), it can be trimmed
shorter (5a.10).
Connect window opener (7090) to (7451)
using spacer (7413) and two screws (7349)
(5a.11) (5a.12).
Connect plastic nut caps (6070) by pushing
them onto all nuts (7053) (5a.13).
5b. toP wINdow
Assemble all parts as in Section 5a.
6a. SlIdINg dooRS
Insert brush seal (7332) into the guides in the
door bars (7352) (7353) (7355) (7356) (7357).
(6a.2) and cut to length.
Loosely assemble wheels (7364), using
spacers (7392) on each side of the wheel, bolt
(7393), jump clip (7350) and lock nut (7360),
onto door bottom bars (7355) (6a.3).
Connect (7355) with door side bars (7357) or
(7358) (6a.3) (6a.7a).
Assemble door middle bars (7354) or (7384)
with lock parts (7400), (7401) and (7402) using
bolts (7404). Connect to door side bars (7357)
or (7358) using bolts (7052), nuts (7053) and
bolts (7405) (6a.4) (6a.5) (6a.8). do not over
tighten bolts (7404) and (7405).
Connect door top bars (7352) or (7353) to
door side bars (7357) or (7358) (6a.6) (6a.7b).
Slide panes G into the glazing channels in the
assembled parts (6a.9).
Loosely prepare (7052) and (7053) in door
side bars (7356) and slide onto (7355), (7354)
or (7384) and (7352) or (7353) fitting the bolt
heads of (7052) into the bolt channels and
the glazing into the glazing channels (6a.9)
(6a.10). Insert door guides (2271) into the top
of both doors (6a.6).
Note - If you have chosen 4mm glass glazing,
cut glazing seal (7420) to fit and press into the
space in the glazing channels on the inside of
the door to fix the glass in place (6a.11).
6b. dooR FRame aNd SteP
Assemble door support (7362) onto the sill bar
in the door opening using bolts (7390) (6b.1)
(6b.2).
Tilt door wheel track (7351) to fit into the sill
bar and lower into position (6b.3). Centre on
the door opening and connect to the founda-
tion using wall plug (2003) and screw (2002)
(6b.4).
Connect door side frames (7361) to middle
bars (7311). When in place connect to the
top using bolt (7052) and nut (7053) (6b.5) -
(6b.8).
At the bottom insert bolt (7052) into the chan-
nel on both sides of door step (7363) (6b.9)
and slide the door step into place (6b.10)
(6b.11).
7. glazINg oveRvIew
Please sort the glazing according to your
model size and glazing type before beginning.
If you have chosen glass then panes E and F
are identical on both sides.
Note - The UV-resistant side of the polycar-
bonate sheets is indicated by a plastic film
or printing at the edge. this side must face
outside. Loosen the film approximately 2cm
at all edges of each pane before assembly.
When the assembly of all sheets is finished
completely remove all film from the sheets.
7a. RooF glazINg / eave
Slide the roof glazing into the guides in the
roof profiles (7a.2) (7a.3). When two adjacent
7
Advertenties
Inhoudsopgave
