Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
IN S TA LLA TION M A N U A L
9.7 Flame baffle plate
Front appliance:
At delivery, the flame baffle plate (see appendix 2, fig. 12 and 13a) is located in the top section of the appliance.
When performing maintenance at the appliance, the flame baffle plate must be removed.
Follow the procedure described below:
Ø
Take hold of the flame baffle plate and lift the rear slightly upwards.
Ø
Slide the flame baffle plate over the ridge to the rear.
Ø
Lower the front of the flame baffle plate and remove the flame baffle plate.
Placing the flame baffle plate takes place in reverse order.
Tunnel appliance:
At delivery, the flame baffle plate (see appendix 2, fig. 12 and 13b) is located in the top section of the appliance.
When performing maintenance at the appliance, the flame baffle plate must be removed.
Follow the procedure described below:
Ø
Remove the four screws from the plate (see appendix 2, fig. 12).
Ø
Grab the flame baffle plate and slide it towards you until the rear is released from the ridge.
Ø
Slide the flame baffle plate to the rear until the front is released from the ridge.
Ø
Lower the front of the flame baffle plate and remove the flame baffle plate.
Placing the flame baffle plate takes place in reverse order.
The stainless steel profiles must be placed on the glass pane sides, with the screw heads at the top
!Caution
(see appendix 2, fig. 13b).
9.8 Supplementary installation instructions per appliance
9.8.1 Odin Front, Wall / Oval Front, Wall
9.8.1.1 Placing the appliance
This appliance must be suspended from a wall.
The Odin Front/Tunnel, Wall may only be mounted on a vertical wall made of robust, non combustible and
!CAUTION
heat-resistant material.
The flue exhaust (niche pipe or connection piece suitable for 150 mm SS pipe) in the ceiling should be 225 mm
!Caution
from the centre to the wall. In all other cases, bends should be used.
When placing the fire, proceed as follows (see appendix 2, fig. 9 and 10). The recommended height between the
bottom of the appliance and the floor is 400 mm (see fig. 9B). The top of the wall bracket will then be suspended
at 875 mm (see fig. 9A):
Ø
Determine the position of the wall bracket and draw it on the wall (fig. 10-4). The recommended height is 875 mm
(fig. 9A), measured from the top of the wall bracket (= 400 mm from the bottom of the appliance to the floor,
fig. 9B).
Ø
Drill holes in the wall and fasten the wall bracket using the supplied key bushes (fig. 10-3) and bolts (fig. 10-2).
Make sure everything is mounted level and that the wall bracket is centrally located under the flue exhaust in the
!Caution
ceiling.
Prior to placing the appliance, remove the door in order to avoid damage and make the installation easier.
!Tip
Ø
Break out the cams at the back of the appliance.
Ø
Suspend the appliance from the wall bracket.
Ø
Adjust the appliance by means of the adjustment plates at the back of the appliance using an open-end wrench,
until the appliance is straight in relation to the wall (fig. 10-7).
Ø
Place the stove pipe (fig. 10-5/6) around the pre-mounted conical ring. If necessary, place the rosette.
9.8.1.2 Installing the stucco guard plate
If the appliance is placed less than 35 cm from a non combustible wall, we recommend installing the stucco guard
plate supplied with the front models. Without this plate, the stucco or the paint layer can be damaged by high
temperatures.
Proceed as follows:
Ø
Allow the guard plate at the back of the glue gas duct to rest on the appliance.
Ø
Then press the plate against the flue gas duct.
Ø
Drill 4 holes (Ø 4 mm) and fasten the plate with the supplied screws (see appendix 2, fig. 16).
This plate does not provide protection against combustible materials!
!Caution
43
Advertenties
Hoofdstukken
Inhoudsopgave
