Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
If the display flashes "
This means that:
• you have not placed a pan on the correct cooking zone or,
• the pan you're using is not suitable for induction cooking or,
• the pan is too small or not properly centred on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 1 minutes if no suitable pan is placed on it.
When you have finished cooking
1. Touching the heating zone selection control that you wish to switch off
2. Turn the cooking zone off by scrolling down to"0" . Make sure the display shows"0",then show"H".
3. Turn the whole cooktop off by touching the ON/OFF control.
4. Beware of hot surfaces "H" will show which cooking zone is hot to touch. It will disappear when the surface
has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat
further pans, use the hotplate that is still hot.
!
Locking the Controls
• You can lock the controls to prevent unintended use (for example children accidentally turning the cooking
zones on).
• When the controls are locked, all the controls except the ON/OFF control are disabled.
To lock the controls
Touch the keylock control. The timer indicator will show " Lo " To unlock the controls
1. Make sure the Induction hob is turned on.
2. Touch and hold the keylock contro for a while
3. You can now start using your Induction hob.
When the hob is in the lock mode,all the controls are disable except theON/OFF , you can always turn the
induction hob off with the ON/OFF control in an emergency,but you shall unlock the hob first in the next
operation
Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the Induction hob. When an excessive
temperature is monitored, the Induction hob will stop operation automatically.
Detection of Small Articles
When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other small item (e.g. knife, fork, key)
has been left on the hob, the hob automatically go on to standby in 1 minute. The fan will keep cooking down
the induction hob for a further 2 minute.
Auto Shutdown Protection
Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you
forget to turn off your cooking. The default working times for various power levels are shown in the below table:
Power level
Default working timer (hour)
When the pot is removed, the induction hob can stop heating immediately and the hob
automatically switch off after 1 minutes.
People with a heart pace maker should consult with their doctor before using this unit.
!
Using the Timer
• You can set it to turn one cooking zone off after the set time is up.
• You can set the timer up to 99 minutes.
Setting the timer to turn one cooking zone off
Cooking zones set for this feature will:
1. Touching the heating zone selection control that you want to set the timer for.
2. Touch timer control , The minder indicator will start flashing and "30" will show in the timer display.
3. Set the time by touching the or control of the timer
Hint: Touch the "-" or "+" control of the timer once will decrease or increase by 1 minute.
Touch and hold the "-" or "+" control of the timer will decrease or increase by 10 minutes.
4. Touching the "-" , to reduce the time outstanding to zero, or press the "timer control", when the "00"
shows in the minute display, the timer is cancelled.
5. When the time is set, it will begin to count down immediately. The display will show the remaining time and the
timer indicator flash for 5 seconds.
NOTE: The red dot next to power level indicator will illuminate indicating that zone is selected.
6. When cooking timer expires, the corresponding cooking zone will be switch off automatically.
!
Other cooking zone will keep operating if they are turned on previously.
" alternately with the heat setting
1
8
2
3
4
5
6
8
8
4
4
4
4
7
8
9
2
2
2
6
or
0
H
6
30
00
36
6.
--
Advertenties
Inhoudsopgave
