Safety Information For Screwdrivers; Product Description And Specifications; Intended Use; Product Features - Bosch Professional GSR 12V-35 FC Oorspronkelijke Gebruiksaanwijzing
Verberg thumbnails
Zie ook voor Professional GSR 12V-35 FC:
- Oorspronkelijke gebruiksaanwijzing (227 pagina's)
Advertenties
Beschikbare talen
Beschikbare talen
16 | English
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Safety information for screwdrivers
Safety instructions for all operations
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring. Cut-
ting accessory or fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
u
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety information
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not modify or open the battery. There is a risk of
u
short-circuiting.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
1 609 92A 9UL | (09.10.2024)
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery in the manufacturer's products.
u
This is the only way in which you can protect the battery
against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal and plastic.
The power tool can be used with a right angle adapter
(GFA 12-W), an off-set angle adapter (GFA 12-E), a bit
holder adapter (GFA 12-X), a drill chuck adapter (GFA 12-B)
or a rotary hammer adapter (GFA 12-H).
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Tool holder
(2)
Torque presetting ring
(3)
Gear selector switch
(4)
Battery release button (2 x)
a)
(5)
Rechargeable battery
(6)
Rotational direction switch
(7)
On/off switch
(8)
Battery charge indicator
(9)
Worklight
(10) Bit holder adapter GFA 12-X
(11) Drill chuck adapter GFA 12-B
(12) Off-set angle adapter GFA 12-E
(13) Right angle adapter GFA 12-W
(14) Rotary hammer adapter GFA 12-H
(15) Locking ring
(16) Handle (insulated gripping surface)
a)
(17) Universal bit holder
a)
(18) Belt clip
a)
(19) Bit holder
a)
a)
a)
a)
a)
Bosch Power Tools
Advertenties
