Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
2 Scope of delivery
IBS/A (29800)
1 pc. IBS/A industrial drill/grinder
1 pc. Charger
1 pc. Battery
1 pc. Storage case
1 pc. Operating instructions
1 pc. Safety guidelines
1 pc. Key
6 pcs. Collets (1.0-1.5-2.0-2.4-3.0 and 3.2 mm)
1 pc. Round grinding pin Ø 5mm
1 pc. Cylinder grinding pin Ø 6mm
1 pc. Cylinder grinding pin Ø 2.5 mm
1 pc. Cup grinding pin Ø 7mm
1 pc. Tungsten carbide micro drill Ø 0.5 mm
1 pc. Tungsten carbide micro drill Ø 1 mm
1 pc. Diamond-coated grinding pin Ø 1.8 mm
1 pc. Finishing miller, ball shaped Ø 2.3 mm
2 pcs. Sanding disc Ø 22mm (pink colour) of high-
grade corundum, for steel, cast iron, HSS
steels
2 pcs. Sanding disc Ø 22mm (grey) For engraving
and frosting of glass, ceramic and stellites,
also for grinding of hard metal, white cast
iron and high-alloy steels
1 pc. Polishing disc for acrylic glass and Plexiglas
1 pc. Brass brush for machining brass, brass
alloys, copper, precious metals, semi-pre-
cious stones, plastic and wood. For cleaning
electronic components and printed circuit
boards.
10 pcs. Corundum cutting discs for cutting alloyed
and non-alloyed steel, stainless steels and
non-ferrous metals. Can also be used to cut
wood and plastic.
1 pc. Clamping arbour shaft diameter Ø 3.2 mm
IBS/A (29802)
1 pc. IBS/A industrial drill/grinder
1 pc. Operating instructions
1 pc. Safety guidelines
1 pc. Key
6 pcs. Collets
(1.0-1.5-2.0-2.4-3.0 and 3.2 mm)
3 Technical data
Device:
Length:
approx. 270 mm
(with battery)
Weight:
Fit:
Voltage:
Rotational
speed:
Noise generation:
Grip vibration:
Charger:
Mains voltage: 100-240 V~,
50/60Hz
Output voltage:
Charging current:
Battery:
Rechargeable lithium-ion battery
Nominal/charging voltage:
Energy/Capacity:
4 Noise/vibration information
The information on vibration and noise emissi-
on has been determined in compliance with the
prescribed standardised and normative measuring
methods and can be used to compare electrical
devices and tools with each other.
These values also allow a preliminary evaluation of
the loads caused by vibration and noise emissions.
Depending on the operating conditions, the emissi-
ons that actually occur may deviate from the values
given above!
This applies in particular depending on the workpi-
ece to be machined and the insert tool (especially
its wear condition). Unsuitable workpieces or ma-
terials, poorly maintained tools, too high a feed rate
or unsuitable insert tools can signifi cantly increase
the vibration load and noise generation.
To more accurately estimate the actual vibration
and noise load, also take the times into considera-
tion where the device is switched off, or is running
but is not actually in use. This can clearly reduce
the vibration and noise load across the entire work
period.
approx. 235 mm
(without battery)
approx. 700 g
(with battery)
approx. 520 g
(without battery)
ø 20 mm
10.8 V
7,000 – 23,000/min
< 70 dB(A)
2
< 2.5 m/s
12.6 V
2 A
10.8 V / 12.6 V
28.2 Wh / 2.6 Ah
- 15 -
Advertenties
Inhoudsopgave
