Inhoudsopgave
Advertenties
EnGLIsh
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D
WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Visible radiation. Do not stare into light.
Do not stare at operating lamp. May be
harmful to eyes.
Date Code Position (Fig. B)
The date code
9
, which also includes the year of manufacture,
is printed into the housing.
Example:
2020 XX XX
Year and week of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Switch
1
Loop hook
2
Pivoting head
3
Battery pack
4
5
Battery release button
Belt hook (optional accessory)
6
Belt hook screw
7
Intended Use
These worklights are professional tools.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
24
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
4
with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
5
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
8
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Fitting the Warning Label
The safety warnings on the label shown on the laser must be
formulated in the language of the user.
For that purpose, a separate sheet of self‑adhesive labels has
been supplied with the tool.
WARNING: Check that the safety warnings on the label
have been formulated in your language.
The warnings should read as follows:
RISK GROUP 2
CAUTION: POSSIBLY HAZARDOUS
OPTICAL RADIATION EMITTED
FROM THIS PRODUCT.
•
If the warnings are in a foreign language, proceed as follows:
-
Remove the required label from the sheet.
Carefully place the label over the existing label.
-
-
Press the label in place.
WALT battery packs and chargers.
e
4
is fully charged.
and firmly pull the battery pack
Advertenties
Inhoudsopgave
