Inhoudsopgave
Advertenties
Boost Function
To use this function, select a cooking zone
and set the desired cooking level, then
press the "P" (Boost) button.
The Boost function can only be activated
if it is applicable with the cooking zone
selected. If the Boost Function is active,
a "P" will be shown on the corresponding
display.
Activating the booster can exceed the
maximum power, in which case the
integrated power management will be
activated.
The necessary power reduction is shown
by the corresponding cooking zone display
blinking. Blinking will be active for 3
seconds to allow for further adaptations of
the settings before power reduction.
Bridge Zone
Switching the Bridge Zone On
Touch the front left and rear left heater
selection buttons simultaneously. A static
dot will be shown on the left heater display.
Displays will show 'b' and 'r', AlSo, touch
the front right And reAr right heAter
Selection Key SimultAneouSly. there
iS A StAtic dot indicAtion on the right
heAterS diSplAyS And diSplAyS will
Show the 'B' And 'r'. The blinking dots will
no longer be displayed.
Select the temperature setting by using the
sliding button. Increase the heat setting by
pressing the right side of the sliding button
or decrease the heat setting by pressing the
left side of the sliding button.
The bridge element will be ready to use.
For the fastest boil time, select the desired
cooking level, then press the "P" key to
activate the Boost function.
Switching the Bridge Zone off
To select the Bridge element, press the rear
left or front left heater selection button and,
using the left side of the sliding button, turn
the level down to "0". If the bridge cooking
zone is hot, "H" will be displayed.
Also right bridge element shall be
selected by pressing the rear right or
front right heater selection key with
using left side of the sliding button
key, turn the level down to ''0''. If the
bridge cooking zone is hot, "H" will be
displayed .
If there is an error, an error code will be shown on the
E1
Cooling Fan is disabled. Call an authorised
E3
Supply voltage is other than the rated values.
Switch the hob off by pressing
"H" disappears for all zones, switch the hob
on by pressing
the same error is displayed again, call an
E4
Supply frequency is different from the rated
values. Switch the hob off by pressing
zones, switch the hob on by pressing
and continue to use. If the same error is
displayed again, switch the plug for the
appliance off and on. Switch the hob on by
pressing
error is displayed again, call an authorised
E5
Internal temperature of the hob is too high,
switch the hob off by pressing
E6
Communication error between the touch
control and heater. Call an authorised service
E7
Coil temperature sensor is disabled. Call an
E8
Cooler temperature sensor is disabled. Call
EA
Large Coil Saturation Error. Switch the hob
off by pressing on/off button, switch the hob
on by pressing on/off button and continue to
use. If the same error is displayed again, call
EC
Supply Voltage Error.Switch the hob off by
pressing on/off button, switch the hob on by
pressing on/off button and continue to use.
If the same error is displayed again, call an
C1-C8
Mcroprocessor alert. Switch the hob off by
pressing on/off button, switch the hob on by
pressing on/off button and continue to use.
If the same error is displayed again, call an
4.2 AcceSSorieS
The Vitroceramic Glass Spatula
Always use the glass spatula to remove
spillages or deposits from the hob before
trying chemical cleaning agents. This is
the ideal method for removing even the
smallest deposits from the hob, and for
removing spillages from hot cooking zones
before they burn onto the hob.
EN - 17
Error Codes
heater displays.
service agent.
and continue to use. If
authorised service agent.
, wait until "H" disappears from all
and continue to use. If the same
service agent.
heaters cool down.
agent.
authorized service agent.
an authorized service agent.
an authorised service agent.
authorised service agent.
authorised service agent.
,wait until
and let the
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
