Inhoudsopgave
Advertenties
Working instructions
1.
Place the wood piece in the jigging device.
Only wood pieces with a max. diameter of 12 cm are allowed to be
sawed.
Pull out the support extension (20) to the desired length and fix it
using the star grip knob (21).
You will get pieces of equal length if you pull out the length stop
(22) and fix it in the desired position using the star grip knob.
2.
Hold the handle (19) on the jigging devcie with both hands and push the
jigging device uniformly towards the saw blade.
movements.
The barbs on the jigging device prevent any turning of the wood
piece during sawing.
Do not force the jigging device against the saw blade, the motor
speed should not drop too far.
3.
After cutting, the jigging device is automatically brought back to its home
position by spring force.
In the home position, all of the saw blade (incl. cutting teeth) is
covered by the saw blade casing.
If the recuperating spring (10) is broken or worn, the jigging
device will not automatically return to its home position. Replace the
recuperating spring.
Never saw without or with a damaged recuperating spring.
4.
Only advance the wood piece after a completed sawing operation.
Maintenance and cleaning
Before each maintenance and cleaning work
− Switch off device
− Wait unitl the saw blade comes to a stop.
−
Pull out power plug
Maintenance and repair work other than those described in this chapter is
only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must unconditionally
be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages and
injuries.
Cleaning
Observe the following to maintain the operability of the machine:
Do not wash down device with water.
Remove shavings and dust only with a brush or vacuum cleaner.
Clean and oil all moving parts regularly.
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid or
environmentally acceptable spray oil.
Take care that the saw blade remain free of rust and resin.
Remove resin residues from the push frame surface.
Resin residues can be removed with a commercial maintenance and care
spray.
The saw blade is a wearing part and will become dull after prolonged or
frequent use.
Renew the saw blade or have it sharpened
All manuals and user guides at all-guides.com
G3
H
Avoid erratic
Maintenance
Changing the saw blade
Remove the mains plug before changing the saw
blade.
Danger of cutting! The saw blade is massive and it could be to slick.
Wear gloves when replacing the saw blade.
Do not use any saw blades made of HSS steel.
Do not use any cracked saw blades or such that have changed their
shape.
Only use well-sharpened saw blades.
Danger of burning! The saw blade is still hot shortly after cutting.
E15
1.
Remove the cover (18).
2.
Release the locking nut (17).
3.
Now, the front saw blade flange (14) and the saw blade (15) can be
removed.
4.
Clean the saw blade flanges (14, 16).
5.
Install a new or sharpened saw blade.
Pay attention to the correct running direction of the saw blade: The
arrow on the saw blade and the arrow on the saw blade casing must point
in the same direction!
6. Position the front saw blade flange again.
7. The further assembly is now done in reverse sequence.
8. Check that the cover (18) is properly secured.
Replacing the plastics insert
Immediately replace the worn or damaged plastics inserts (24).
1.
Loosen the screws of the plastics insert and remove them.
2.
Insert a new plastic insert and screw it tightly in place.
Replacing the recuperating spring
Immediately replace a worn or damaged recuperationg spring.
1.
Remove one end of the safety chain (12).
2.
Remove the cotter pin (9) and pull out the bolt (6)from the bracket.
3.
Remove the recuperating spring (10).
4.
Slide a new recuperating spring on the bolt.
5.
The further assembly is now done in reverse sequence.
Transport
Remove mains plug before each transport.
Storage
Pull out power plug
Store unused equipment in a dry, locked place out of the reach of children.
+
Before a longer period of storage carry out the following to extend the saw
+
service life and ensure an easy operating:
− thoroughly clean the device
− treat all movable parts with an environmentally friendly oil
Never use any grease!
E14
E12
E13
D
B2
13
Advertenties
Hoofdstukken
Inhoudsopgave
