Inhoudsopgave
Advertenties
GB
markings identifying the terminals in your plug, proceed as follows.
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-
facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a
faulty hanging due to the drilling and the setting up of plugs.
GB
1) Draw a vertical line onto the wall from the centre of the cooking appliance up to the ceilling, using a
spirit level and a marker pen as illustrated in Fig. 1 - item 1. This is to ensure the correct alignment
of the chimney hood.
2) Place the brackets item 2 on the wall about 1 or 2 mm from the ceiling or from the upper limit, aligning
its centre on the vertical line. Mark the two eyelet holes of the bracket onto the wall. Drill the holes
for the fixing bracket using an 8 mm masonry bit. Fix the chimney bracket item 2 using the 4.5 x 50
mm screws and rawl plugs supplied.
3) Mark a point on the vertical line at a distance d from the cooking appliances of 1217 mm:
d = height fixing splashback (512 mm) + 705 mm (Measurement with splashback).
The distance H is the minimum height in mm from the cooking appliances to the bottom edge item 3 of
the front panel of the hood. Draw a horizontal line through the vertical as illustrated in Fig. 1.
Splashback : When a splashback is to be fitted, the distance between the hood and the cooking appliances
will be determined by the height of the splashback item B and whether or not there is a raised back
on the worktop. The splashback is to be installed before installing the canopy. If the splashback is to
be fixed to the wall using both the top and bottom fixing holes, Care must be taken to ensure that the
splashback is fitted at the correct height before fixing the base units or at least the worktop covering
them. As this is a complex operation, it should only be undertaken by the technician installing the
kitchen units or by a competent person who knows the final dimensions of the units.
Mark the hole centres for the 4 splashback fixing and drill the 4 fixing holes using an 8 mm masonry
bit. Tighten 4 screws on the wall till leaving a space so that the splashback can be hanged behind
the heads of screw. Hang the credence and check the level.
Mark the hole centres for the canopy fixing brackets item 4 at item B mm as illustrated in Fig. 3.
Drill the 4 holes for the fixing brackets using an 8 mm masonry bit. Fix the wall brackets item 4 using
the 4.5 x 45 mm screws and rawl plugs supplied.
4) Hook the canopy item 5 onto the wall brackets item 4 as illustrated in Fig. 3. Lean the hood on the
splashback by unscrewing the 2 screws and to ensure the cooker hood is aligned correctly adjust
the same screws on the top of the canopy as illustrated in Fig. 3. When the hood is aligned correctly
mark the hole centre on the wall for the security fixing screw item8, which is located in the right hand
bracket on the top of the canopy. Unhook the canopy from the wall and drill the hole for the security
fixing screw. Hook the canopy onto the wall and fix the No 4,5 x 50mm headed screw and rawl plug
to secure the canopy to the wall.
5) Ducting:
The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker
hood is ducted to the outside, charcoal filters are not required.The ducting used must be 150 mm (6
INS), rigid circular pipe and must be manufactured from fire retardant material, produced to BS.476
or DIN 4102-B1. Wherever possible use rigid circular pipe which has a smooth interior, rather than
the expanding concertina type ducting.
Maximum length of ducting run:
- 4 metres with 1 x 90° bend.
- 3 metres with 2 x 90° bends.
- 2 metres with 3 x 90° bends.
8
All manuals and user guides at all-guides.com
Advertenties
Inhoudsopgave
