Inhoudsopgave
Advertenties
• Keep the power cord away from heat sources, sharp edges, and objects with moving parts.
• If you use an extension cable, pay attention to its maximum capacity.
• In the event of a malfunction, cease use of the device immediately, press the power button, and unplug
the power cord to avoid overheating, smoke generation or electric shock.
• If the device produces unusual noises or smells, cease operation immediately.
• Never attempt to repair, disassemble or modify the appliance.
• Do not expose the device to rain or water, or place it in a bathroom or other damp area.
• Never use the device without the dirty water tank inserted.
• Do not use the device for any purpose other than cleaning.
• This appliance is only suitable for domestic use.
• Cease use if the nozzle becomes blocked by foreign objects. Do not resume operation until the nozzle is
clear of obstructions.
• Do not sit or lean on the device.
• Ensure that you unplug the power cord from the mains after use.
• Do not vacuum the following items: sand, gravel, dry dust, sharp objects such as glass or drawing pins,
plastic bags, stockings, items that may clog the nozzle or hose;
• The clean water tank should neither be filled with tap water over 40°C nor with harsh alkaline solutions.
• Not suitable for sensitive textiles and surface materials such as: embroidery, silk fabrics, viscose, fur,
leather products, painted or unpainted wooden surfaces, etc.
• Do not tip or drop the hose when filled with water. This can cause water to leak out and the floor to
become wet.
• If too much foam forms in the dirty water tank during use, stop use immediately before it exceeds the
water level, and empty the dirty water tank before further use.
• When using cleaning products, be careful not to damage the object being cleaned.
• When using the device, ensure that the suction inlet at the base is not blocked.
• Unplug the appliance's power cable when not in use or when cleaning.
• Accessories not included in the scope of delivery must not be used.
Consumables (see Fig. #2)
• Ensure that the filter nets are correctly installed before each use. (Filter nets are delivered pre-installed)
• To check the large filter, remove the round lid inside the dirty water container by turning it anti-clockwise.
• Do not use the device if the filter net is damaged or is not inserted.
• Replace the filter nets regularly if they are very dirty.
Replacement filters are available at: www.mediashop.tv
PRODUCT ASSEMBLY
Step 1 (see Fig. #3)
1. First, remove all parts from the packaging, and check that the scope of delivery is complete.
2. Attach the included nozzle holder by sliding it into the tabs on the right or left side of the device,
depending on your preference.
NOTE: When carrying the device, insert the 3-in-1 nozzle attachment into the designated nozzle
holder on your Livington Spot Blast.
Step 2 (see Fig. #4)
1. Insert one end of the suction hose into the socket on the device. To insert it, unlock the connection on the
hose by pushing the locking slide downwards.
2. Press the release button to insert the hose into the socket. You will hear a click to indicate that the hose
is fully connected.
3. At the end, lock the connection on the hose by pushing the locking slide upwards.
4. To remove the suction hose, unlock the connection again by sliding the locking slide, pressing the
unlocking button again, and pulling the hose out of the socket.
Step 3 (see Fig. #5)
1. Connect the 3-in-1 nozzle attachment to the end of the suction hose. To insert it, unlock the connection on
the hose by pushing the locking slide downwards.
2. Press the release button to insert the 3-in-1 nozzle attachment into the suction hose. You will hear a click
to indicate that the nozzle attachment is fully connected.
3. To remove the nozzle attachment, unlock the connection again by sliding the locking slide, pressing the
unlocking button again, and pulling the nozzle attachment out of the suction hose.
Step 4 (see Fig. #6)
1. Unscrew the cap on the clean water tank, and fill it with tap water or a non-foaming cleaning solution.
2. When the clean water tank is full, screw the lid back on and return it to its place in the device.
CAUTION: Make sure that the clean water tank lid is properly closed. For the clean water tank,
only use tap water below 40°C or a non-foaming cleaning solution (mild detergent mixed with
water), otherwise excessive foaming and device failure may occur. Empty the clean water tank
immediately after use. Leaving water in the tank can cause leaks or allow the growth of mould.
USE
Step 1
• Plug the power cord into the mains. Ensure that the power switch is turned off.
6
Step 2
• Press the On/Off button. The device switches on.
Step 3
1. Hold the 3-in-1 nozzle attachment over the stain, and spray clean water or a non-foaming cleaning
solution by pressing the spray button.
NOTE: In order for the 3-in-1 nozzle attachment to spray, the device must be switched on. If the
device is turned off, the spray function will not work.
2. Now place the 3-in-1 nozzle attachment on the stain, and brush over it in a way that prevents the stain
from spreading further. (see Fig. #7)
3. To extract all the liquid from the textile fibres, press the 3-in-1 nozzle attachment against the surface and
draw it backwards.
4. The dirty water is collected in the dirty water tank as your Spot Blast sucks it up.
5. Repeat this process as many times as necessary until the stain is completely removed.
Step 4
1. When finished, press the On/Off button. The device switches off.
2. Unplug the power cord from the mains.
3. Empty the clean and dirty water tanks, and wash the dirty water tank, the inside of the hose and the filter
nets thoroughly before storing it. (see section "Cleaning the device")
NOTE: We recommend allowing the device base to dry after each use to avoid development of any
unpleasant odours during storage. Please remove the 3-in-1 nozzle attachment, the suction hose,
the clean water tank and the dirty water tank and leave the device to run empty for 5-10 minutes,
so that the suction can dry it from the inside.
For stubborn stains and dirt:
1. Pre-treat the stain and before using the device by applying a suitable cleaning agent to the stain and
allowing it a few minutes to take effect. Follow the respective cleaning agent's instructions for use.
NOTE: When using a cleaning product, first perform a test on an inconspicuous area of the surface
to be cleaned to ensure no discolouration or other problems occur before use. Do not use thinners,
essential oils, chlorine-based bleach or flammable solvents. These could cause discolouration, a
malfunction, or even a fire.
2. Use the brush attached to the 3-in-1 nozzle attachment to loosen stubborn stains by scrubbing. (see Fig.
#8)
3. As soon as the stain has loosened slightly, spray water or cleaning solution onto it using the spray button
and then vacuum over the stain with the nozzle attachment.
4. For better results and to avoid residue, draw the 3-in-1 nozzle attachment over the dirt as many times as
necessary. (see Fig. #9)
5. Repeat the process if necessary.
NOTE: If the foam in the dirty water tank has exceeded the "full" water line, the device will
automatically stop all functions. Otherwise, water droplets could enter the main motor and cause
damage to the device. To continue use, you must empty the dirty water tank.
CLEANING AND MAINTENANCE OF THE DEVICE
Washing the dirty water tank
1. If the dirty water in the dirty water tank has reached the full water line, cease operation immediately and
turn off the device.
2. Remove the dirty water tank by holding the handle and lifting it upward until the entire container is clear
of the unit. Never pull the dirty water tank backwards, as it is locked to the device by the ribs on the sides.
3. Open the lid by lifting the tab.
4. Thoroughly wash the dirty water tank using tap water. Don't forget to also remove the round lid inside by
turning it anti-clockwise. This allows you to access the filter inside. Washing the filters after each use
ensures optimal performance and inhibits the development of unpleasant odours. (see Fig. #2)
5. Reinsert the filters once they have dried. Close the round lid in the dirty water tank, close the tank lid, and
put it back in place.
Washing the clean water tank
1. With the device switched off, remove the clean water tank by lifting it upwards.
2. Unscrew the cap at the bottom by turning it anti-clockwise.
3. Allow the remaining cleaner to drain out before thoroughly rinsing the container with water.
4. Once it is dry, screw the cap back on. The clean water tank is leak-proof and ready for use.
CAUTION: If the dirty water tank is not emptied once it reaches full capacity, suction will
automatically stop to prevent damage to the motor. The automatic suction may also be stopped by
too much foam. If the inside of the motor is wet, please remove the 3-in-1 nozzle attachment, the
suction hose, the clean water tank and the dirty water tank and leave the device to run for 5-10
minutes so that the suction can dry it from the inside.
Cleaning the device
1. Remove the dirty water and clean water tanks, the 3-in-1 nozzle attachment, the hose and the small filter.
Advertenties
Inhoudsopgave
