Inhoudsopgave
Advertenties
● Automatic suction speed function (VOC function):
This product is equipped with a sensor (VOC sensor) that
modulates the suction speed automatically according to the
amount of smoke detected.
This function must be enabled manually via the Radio
Control or via the Elica Connect App.
When the function is active, LED L1 will light up White.
Once activated, if the sensor detects no smoke for a few
minutes, the motor will be switched off.
Note: The function will still remain active and if within the
next 2 hours the sensor detects some steam, the motor
will be restarted automatically. After 2 continuous hours
without detecting any smoke, the function is disabled. It is
always possible to disable this function manually, at any
time, via the Radio Control or via the Elica Connect App.
● VOC sensor calibration:
Calibration is necessary to allow the product sensor to work
correctly; calibration is performed in two ways:
Automatic: each time the hood is reconnected to the
mains (e.g. the first time it is installed or after a power
failure).
Manual: Manual calibration requires that the product motor
is OFF and that normal environmental conditions persist in
the room where it is installed. This operation must be
performed when automatic operation is unsatisfactory.
With Radio Control 1:
Simultaneously press A+D for 2 sec.
With Radio Control 2:
This procedure is described in the Radio Control manual.
During calibration, LED L1 flashes Green.
To cancel the current calibration, repeat the procedure
used to start the calibration.
● Hob settings (for VOC sensor)
To use the VOC function in the best way possible, it is
necessary to select the correct type of hob from those
available: GAS - Induction or Electric. By Default, the hob
is set to GAS.
This setting requires that the product motor is OFF and that
the VOC sensor is deactivated.
With Radio Control 1:
Simultaneously press keys B+D for 2 sec. an acoustic
signal will indicate that you have entered the hob setting
menu. From here, use the keys B and C to scroll back and
forth to select the desired hob. Each time the key is
pressed, a type of hob will be selected; LED L1 will light up
in a different colour according to the selected hob: Green =
Gas; Yellow = Electric; Cyan = Induction.
With Radio Control 2:
Simultaneously press keys A+D for 2 sec. From here, use
the keys B and C to scroll back and forth to select the
desired hob. Each time the key is pressed, a type of hob
will be selected; LED L1 will light up in a different colour
according to the selected hob: Green = Gas; Yellow =
Electric; Cyan = Induction.
Note: after resetting the hob type, to a type other than the
Default one or the previous one, an automatic calibration of
the VOC sensor will start. See the chapter on this function.
CONTROLLING THE PRODUCT VIA WI-FI
The are two product control modes via Wi-Fi; to do this, it is
necessary to download the Elica Connect App and follow
the instructions given.
• Elica Cloud mode
This feature allows the product to be controlled from a
mobile device, even when away from home.
• Direct Control mode
This feature allows the product to be controlled from a
mobile device, as if it were the Radio Control.
● Wi-Fi configuration:
Follow the instructions provided in the Elica Connect App
for the Wi-Fi configuration. During the configuration
procedure, LED L2 will light up indicating the connectivity
status (see the Wi-Fi status table below). To interrupt the
Wi-Fi configuration procedure, press key A on the Radio
Control for about 2 sec. when LED L2 on the hood is lit up
and is flashing fast.
● Wi-Fi configuration reset:
This operation is used to reset the product to the factory
configuration.
With Radio Control 1:
press keys A+B for 2 sec.
With Radio Control 2:
press keys D+E for 2 sec.
Note: The password and all other settings made from the
Elica Connect App will be reset and will need to be set
again.
● Wi-Fi On/Off:
After the configuration, the Wi-Fi can be switched on / off.
With Radio Control 1:
Press key A for 2 sec.
With Radio Control 2:
This procedure is described in the Radio Control manual.
Note: Switching off the Wi-Fi with this procedure does not
result in the loss of the previously saved parameters.
WI-FI STATUS TABLE
LED L2
Light off
Steady white
light
12
Wi-Fi Status
WiFi not configured or off
WiFi connected
Advertenties
Inhoudsopgave
