Inhoudsopgave
Advertenties
Radio Control must be paired.
Depending on the product purchased, you will find one of
the two Radio Controls shown in the figure:
Radio Control 1:
Radio Control 2:
The pairing instructions are given in the manual supplied
with the Radio Control.
When the Radio Control has been paired, both LEDs L1
and L2 on the hood will flash White.
Attention!: the main functions are indicated in the Radio
Control manual; the manual also contains other indications
of use and other functions with an explanation of how to
activate them using the Radio Control. In cases where no
reference is made to a specific Radio Control, the
indications are valid for both.
Note: The two Radio Controls are interchangeable, so it is
always possible to purchase the one not included with the
product from the store at www.elica.com.
●
OPTIONAL OPERATION:
Hob selection.
The product is designed to adapt its performance in the
best way possible according to the hob on which it works.
By Default, the product is set to work with GAS hobs.
To change this setting, after pairing the Radio Control, see
the chapter "Hob settings".
●
AUTOMATIC OPERATION:
VOC sensor calibration
If the optional hob selection operation is NOT performed,
the VOC sensor calibration starts automatically 2min.
after the product has been connected to the mains.
Calibration lasts 5 min. LED L1 flashes Green and
switches off at the end of the calibration procedure.
Please note! During calibration, the motor is switched
on at speed 1. For more details on the VOC sensor, refer
to the chapters dedicated to this function below.
USING THE CONTROLS
● Suction speed
This product is equipped with 5 suction speeds including 2
timed booster speeds:
Booster 1 (speed 4) timed 15 min.
Booster 2 (speed 5) timed 5 min.
After the minutes indicated above, the suction speed will go
back to speed 2 automatically.
● Delay off
Using the Radio Control, it is possible to program the
delayed switch-off according to the suction speed (power)
active at that time; the speeds at which this function can be
enabled are the following:
Speed 1 (low extraction): 20 min.
Speed 2 (medium extraction): 15 min.
Speed 3 (high extraction): 10 min.
Note (only for products with Wi-Fi function): The Delay
off function can be programmed in a more advanced way,
when connected to the Elica Cloud, via the Elica Connect
App. However, in this case, it will not be possible to
manage the Delay off function from the Radio Control, until
the Wi-Fi is reset or switched off.
● Activating/Deactivating the filter saturation indicator
light
To be performed with the product switched off. The
carbon filter saturation indicator light is usually deactivated,
while the grease filter saturation indicator light is usually
activated.
With Radio Control 1:
Odour Filter: Simultaneously press keys A+B+D for 2 sec.
each press switches sequentially from active to inactive.
(Active = LED L1 steady Red and LED L2 flashing Red.
Inactive = LED L1 steady Red and LED L2 Off)
Grease Filter: Simultaneously press keys A+B+C for 2
sec. each press switches sequentially from active to
inactive. (Active = LED L1 steady Orange and LED L2
flashing Orange. Inactive = LED L1 steady Orange and
LED L2 Off)
Wait 10 sec. to save the chosen setting.
With Radio Control 2:
This procedure is described in the Radio Control manual.
Wait 10 sec. to save the chosen setting.
● Filter saturation indicator lights
The LEDs on the hood indicate the need to perform
maintenance on the filters.
Odour filter: L1 + L2 flashing Red.
Grease filter: L1 + L2 flashing Orange.
Note: The filter saturation indication is visible for 10 sec.
when the hood is switched on. After performing
maintenance on the filters, it is necessary to perform the
filter saturation reset.
● Filter saturation reset
This operation must be performed within the first 10sec.
after switching on the product.
The procedure is described in the Radio Control manual.
Note: If there are two active warnings, for both grease and
odour filters, the operation must be performed twice.
11
Advertenties
Inhoudsopgave
