Inhoudsopgave
Advertenties
5.6 Guard hood for use with the cutting blade
(Fig. 7)
Caution! The cutting line cover (D) must be re-
moved if you want to work with the cutting blade.
Take care not to cut yourself on the cutting line
cutter.
Slacken the two retaining screws (E) on the cut-
ting line cover.
Start at the side and carefully press in the lugs (F)
and pull the cutting line cover (D) up and off .
5.7 Guard hood for use with the cutting line
(Fig. 7)
Caution! The cutting line cover (D) must be fi tted
if you want to work with the cutting line. Take care
not to cut yourself on the cutting line cutter. Start
at the side and press the lugs (F) of the cutting
line cover back in and secure them with the two
screws (E).
5.8 Fitting/removing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figs. 8a - 8d. Note the detailed drawing
8e. Warning! Take care not to cut yourself on the
cutting blade.
a) Fitting the cutting blade
Important! If the spacer between the cutting bla-
de and the motor housing (detailed drawing
8e / fi g. 8a / Item 27) slips off the motor shaft (M)
during dismantling, push it back onto the motor
shaft as shown in the drawing.
1. Fit the cutting blade (21) in place.
2. The pressure plate (23) must be fi tted with
the higher edge facing the cutting blade (de-
tailed drawing 8d).
3. Fit the pressure plate cover (24).
4. Screw the size M10 hex nut (25) in place.
Warning! For safety reasons, self-locking
nuts are allowed to be used only once without
exception.
5. Press the locking lever (12) and lock the mo-
tor shaft. Tighten the hex nut using the multi-
function tool (22).
6. Check whether the blade (21) can rotate free-
ly after you let go of the locking lever. If this is
not the case, have the mechanism checked
by an expert.
Important! Vibrations when using the cutting
blade
If considerable vibrations of an unusual nature
arise when using the cutting line after you have
fi tted the cutting blade, this is because the cutting
blade is not fi tted in central position. Switch off the
Anl_Agillo_18_200_SPK13.indb 25
Anl_Agillo_18_200_SPK13.indb 25
GB
tool immediately. Remove the battery/batteries
and refi t the cutting blade.
Caution! A cutting blade that is not fi tted in cen-
tral position will cause damage to the tool!
b) Removing the cutting blade
Press the locking lever and lock the motor shaft.
Unscrew and the hex nut and remove the pressu-
re plate cover, pressure plate and cutting blade.
Each time before use, check the following :
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.
5.9 Using the harness
Caution! Always use the harness when working
with the equipment (Fig. 2/Item 20). Always switch
off the equipment before you release the harness
– risk of injury!
•
Fit the harness (Fig. 9)
•
Hook the equipment to the harness (Fig. 10).
•
Adjust to the perfect working and cutting po-
sition using the various harness adjusters on
the harness. The strap attachment (Fig. 11/
Item 4) can be moved on the top part of the
long handle if required. To do so, slacken the
wing nut on the strap attachment, move the
strap attachment and then re-tighten the wing
nut.
•
To establish the optimum length of the har-
ness, you should then make a few swinging
movements without starting the motor (Fig.
12).
The harness is fi tted with a quick-release mecha-
nism. Pull the red part of the harness (Fig. 13) if
you need to remove the equipment quickly.
5.10 Installing the battery
Push the rechargeable batteries into the batte-
ry mounts provided on the left and right on the
equipment (Fig. 2/Item 1). The battery will be
heard to click into place when it has been pushed
fully in (Fig. 1). To take out the battery, press the
pushlock button (Fig. 15/Item K) and remove the
battery.
5.11 Charging the battery (Fig. 15a)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
- 25 -
09.08.2023 10:22:19
09.08.2023 10:22:19
Advertenties
Inhoudsopgave
