Inhoudsopgave
Advertenties
Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated
on the nameplate.
Caution! Damage due to deep discharge of battery
f Always switch the appliance off with the on/off
switch after use (Fig. 3ⓑ).
f Always switch the appliance off with the on/off
switch when charging the battery (Fig. 3ⓑ).
Charging the battery
Before the appliance is used for the first time, it
should be charged for approx. 16 hours!
1. Connect the appliance plug (J) on the plug-in transformer to
the appliance socket (D) (Fig. 2).
Battery overcharging is prevented thanks to intelligent
charge management.
2. Insert the plug-in transformer into the mains socket.
3. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
·
During charging, the charging indicator light (C)
is illuminated.
·
For the appliance to charge to full capacity, it
should take around 16 hours.
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3ⓐ/ⓑ).
·
When the battery is fully charged, the appliance
can be used for up to 100 minutes without mains
connection. The full capacity is attained after
approx. 5 - 10 charging cycles.
·
In case of insufficient maintenance of the
blade set, the operating time can be reduced
considerably.
Mains operation
1. Connect the appliance plug (J) on the plug-in transformer to
the appliance socket (D) (Fig. 2).
2. Insert the plug-in transformer into the mains socket.
3. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3ⓐ/ⓑ).
Operation
Cutting with the attachment comb
The appliance can also be operated with an attachment comb.
The following attachment combs are included as standard:
·
Attachment comb small = cutting lengths 3 mm and 6 mm
·
Attachment comb large = cutting lengths 9 mm and 12 mm
·
The cutting length (in mm) is shown on the comb.
·
One attachment comb can be used for two differ-
ent cutting lengths.
·
For the second length, all you need to do is
remove the attachment comb, rotate and replace.
·
The advantage of these attachment combs is that
no matter the angle at which you approach the
hair, you always achieve the same cutting length.
Attaching/removing the attachment comb
1. Fit the attachment comb onto the cutting edge of the
blade set.
2. Push the attachment comb on the blade set towards the
housing until it clicks into position (Fig. 4ⓐ).
3. The attachment comb can be removed by pushing it in
towards the cutting edge (Fig. 4ⓑ).
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the appliance before cleaning it or per-
forming any maintenance and disconnect it from
the mains.
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
f Only reconnect the appliance to the power supply
if it is completely dry.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance
and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Accessories and spare parts are available from your
dealer or our service centre.
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
9
Advertenties
Inhoudsopgave
