Inhoudsopgave
Advertenties
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Starting Operation
Setting the rotational direction (see figure B)
The rotational direction switch (16) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (17) is being pressed.
Rotate clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the
tion.
Rotate anti-clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the
tion.
Setting the Operating Mode
Drilling
Set the mode selector switch (8) to the
"drilling" symbol.
Screwdriving
Set the mode selector switch (8) to the "screw-
driving" symbol.
GSB 18V-110 C:
Impact drilling
Set the mode selector switch (8) to the "impact
drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(17).
The LED (13) lights up when the on/off switch (17) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (17).
Adjusting the speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (17) to varying extents.
A light pressure on the on/off switch (17) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Bosch Power Tools
Preselecting torque (applies to screwdriving mode)
The torque presetting ring (7) can be used to preselect the
required torque in 25 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
Only operate the gear selector (9) when the power
u
tool is not in use.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
You can preselect two speed ranges with the gear selector
(9).
Gear se-
Speed
lector
switch (9)
position
1
Low
2
High
posi-
posi-
Temperature-dependent overload protection
When used as intended, the power tool cannot be over-
loaded. In the event of overloading or the temperature
rising/falling outside the permitted operating temperature
range, the speed will be reduced. The power tool will not run
at full speed again until the permitted operating temperature
has been reached.
Activation of the temperature-controlled overload protector
is indicated by the LED (14) on the power tool lighting up
red. To return to within the permitted operating temperature
range, switch the gear selector (9) to first gear, run the
power tool at no load or wait until the LED (14) goes out.
When the LED (14) has gone out, the tool has returned to
within the permitted operating temperature range.
Emergency switch-off (KickBack Control)
The rapid shut-off function (KickBack Con-
trol) gives the user greater control over the
power tool and offers them better protec-
tion than power tools that do not have Kick-
Back Control. The power tool will switch off
if it suddenly and unforeseeably rotates around the
drilling axis.
Rapid shut-off is indicated by the LED on the power tool
flashing.
To switch the tool back on, release the on/off switch and
then press it again.
It will no longer be possible to switch the power tool
u
on if the KickBack Control function is faulty. Have the
English | 19
Torque
Application range
High
For heavy-duty ap-
plications:
e.g. drilling and
screwdriving with
large diameters
Low
For light-duty ap-
plications:
e.g. drilling and
screwdriving with
small diameters
1 609 92A 9RS | (12.06.2024)
Advertenties
Inhoudsopgave
