Inhoudsopgave
Advertenties
18 | English
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
Inserting the GCY 30-4 Bluetooth® Low Energy
Module (accessory)
Read the corresponding operating instructions for informa-
tion about the GCY 30-4 Bluetooth® Low Energy Module.
1 609 92A 9RS | (12.06.2024)
to
Auxiliary handle
Do not operate your power tool without the auxiliary
u
handle (4).
Before carrying out any work, make sure that the aux-
u
iliary handle is tightened. Loss of control can cause per-
sonal injury. Ensure that the auxiliary handle is tightened
with a torque suited to the fastening method; fasten this
to the power tool so that any movement of the auxiliary
handle around or along the drilling axis is avoided.
Fitting the auxiliary handle
Capacity
To open the auxiliary handle, turn the lower gripping end of
60–100 %
the auxiliary handle (4) in an anticlockwise direction.
30–60 %
Pull back the intermediate piece of the auxiliary handle (5)
5–30 %
and hold it in this position.
Slide the auxiliary handle over the drill chuck to mount the
0–5 %
auxiliary handle on the power tool.
Then let go of the intermediate piece (5).
Afterwards, turn the lower gripping end of the auxiliary
handle (4) clockwise to retighten it.
Swivelling the auxiliary handle
Capacity
You can swivel the auxiliary handle (4) to any angle for a safe
80–100 %
work posture that minimises fatigue.
Turn the lower gripping end of the auxiliary handle (4) anti-
60–80 %
clockwise and swivel the auxiliary handle (4) into the re-
40–60 %
quired position. Afterwards, turn the lower gripping end of
20–40 %
the auxiliary handle (4) clockwise to retighten it.
5–20 %
Setting the drilling depth
0–5 %
You can use the depth stop (3) to set the required drilling
depth X.
Loosen the wing bolt for adjusting the depth stop (6) and in-
sert the depth stop into the auxiliary handle (4).
Pull the depth stop (3) far enough out that the distance
between the drill bit tip and the edge of the depth stop (3)
corresponds to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (6).
Changing the tool (see figure A)
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (17) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
Bosch Power Tools
Advertenties
Inhoudsopgave
