Inhoudsopgave
Advertenties
OBJ_BUCH-66-008.book Page 13 Wednesday, December 11, 2013 10:46 AM
This start-up time can be shortened by striking the chisel in
the machine against the floor one time.
To save energy, only switch the power tool on when using it.
Setting the Impact Rate
The electronic control enables stepless speed preselection in
accordance with the material to be worked.
The constant electronic control keeps the preselected impact
rate nearly constant between no-load and load conditions.
– Select the impact rate with the thumbwheel 5 according to
the material.
Changing the Chiselling Position (Vario-Lock)
The chisel can be locked in 12 positions. In this manner, the
optimum working position can be set for each application.
– Insert the chisel into the tool holder.
– Push the chisel adjustment ring 3 forward and turn the
chisel to the required position with the chisel adjustment
ring 3.
– Release the chisel adjustment ring 3 and turn the chisel un-
til it latches.
Working Advice
Before any work on the machine itself, pull the mains
plug.
Sharpening Chisels (see figure C)
Good results are only achieved with sharp chisels; therefore,
sharpen the chiselling tools in good time. This ensures a long
service life of the tools and good working performance.
Re-sharpening
Sharpen chiselling tools using grinding wheels (e. g. ceramic
bonded corundum wheel) with a steady supply of water. Ref-
erence values are shown in the figure. Take care that no an-
nealing coloration appears on the cutting edges; this impairs
the hardness of the chiselling tools.
For forging, heat the chisel to between 850 and 1050 °C
(bright red to yellow).
For hardening, heat the chisel to approx. 900 °C and quench
in oil. Then anneal in an oven for approx. one hour at 320 °C
(annealing colour = light blue).
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Bosch Power Tools
Service Indicator 6
When the carbon brushes are worn out, the machine switches
itself off. This is indicated approx. 8 hours beforehand by the
lighting or blinking of the service indicator 6. The machine
must then be sent to an after-sales service agent. Addresses
are listed in the Section "After-sales Service and Application
Service".
After-sales Service and Application Service
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
English | 13
1 609 92A 0GT | (11.12.13)
Advertenties
Inhoudsopgave
