Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
1.
Device overview – GridLine Vario workbench
The device overview (in addition to the worktop) depends on the configuration se-
lected.
2.
General instructions
Read the instructions for use, follow them and keep them available for later
reference.
3.
Safety
3.1.
SYMBOLS AND MEANS OF REPRESENTATION
Warning symbols
CAUTION
NOTICE
i
3.2.
GROUPED SAFETY MESSAGES
CAUTION
Workbench tipping over
Risk of injury to hands, feet and body due to unrestrained objects falling and risk of
the workbench tipping due to incorrect loading.
»
Wear foot protection and safety gloves.
»
Do not store pointed or other workpieces without restraint.
»
Do not open several drawers at once.
»
Anchor the workbench to the floor.
»
Comply with the maximum load capacity of the individual drawers and storage
shelves.
»
Comply with the maximum load capacity of the workbench.
3.3.
INTENDED USE
Use the workbench only when it is in a good condition. If any faults occur which
may affect safety, have them rectified without delay.
Only attach components at the holes intended for this purpose.
Use exclusively approved Hoffmann Group accessories for modification or re-
building.
For work in indoor industrial environments. For use on dry solid floors.
Operate only in a dry environment.
3.3.1.
Support leg
Support leg for installation on the worktop of the GridLine Vario workbench.
Installation only in conjunction with a rear panel, drawer casing or stabilising
plates.
Cable ducts in the leg for laying connecting cables.
3.3.2.
Stabilising plate
Stabilising plate for installation on the worktop and support leg of the GridLine
Vario workbench.
For stiffening and stabilising the workbench.
Double stabilising plate: for connecting two worktops. For flush alignment of two
worktops, the joint strip must also be installed.
3.3.3.
Rear panel and storage shelf
Rear panel or storage shelf for installation on the support leg of the GridLine
Vario workbench.
Installation as a storage shelf only in conjunction with the stabilising plates.
Storage shelf for storage of workpieces and tools.
Rear panel as a modesty board and for stabilising the workbench.
Perform installation only on a workbench with two support legs.
Mount only on suitable holes.
Comply with the maximum load-bearing capacity.
3.3.4.
Casing
Size 200 to 500 and 800 to 900 for installation on a GridLine Vario workbench.
For installation up to and including size 500 in conjunction with a support leg.
From size 800 the casing replaces the support leg. Select the height to corres-
pond to the opposite support leg or casing.
Comply with the maximum load-bearing capacity.
Drawers for storage of tools.
Storage shelf for storage of workpieces and tools.
Mount only on suitable holes.
3.4.
IMPROPER USE
Do not place or position on the workbench. Not for transporting people.
Not for use in areas where the floor slopes upwards or downwards.
Do not use in explosion hazard areas.
No do expose it to water, precipitation or contamination.
Not for use in areas where the floor is loose or unpaved.
Do not overload the workbench, worktop, drawers or storage shelves.
Do not make any unauthorised modifications.
Meaning
Indicates a hazard which if not avoided
may lead to minor or moderate injury.
Indicates a hazard which if not avoided
may lead to damage to property.
Indicates useful tips and instructions to-
gether with information for efficient and
problem-free operation.
3.5.
PERSONNEL QUALIFICATIONS
Specialists for mechanical work
Specialists in the sense of this documentation are persons who are familiar with as-
sembly work, mechanical installation, commissioning, troubleshooting and mainten-
ance of the products and who possess the following qualifications:
Qualification / training in the field of mechanics as specified in the nationally ap-
plicable regulations.
Trained person
Trained persons in the sense of this documentation are persons who have been
trained to perform work in the areas of transport, storage and operation.
3.6.
PERSONAL PROTECTIVE EQUIPMENT
Comply with the national and regional regulations for safety and accident preven-
tion. Protective equipment such as safety shoes and safety gloves appropriate for the
risks associated with the intended activities must be selected, provided and worn.
3.7.
DUTIES OF THE OPERATING COMPANY
Ensure that all the work listed below is performed only by qualified specialists:
Transport and installation location
Installation
Maintenance
The operating company must ensure that personnel who work on the product com-
ply with the regulations and provisions together with the following instructions:
National and regional regulations for safety, accident prevention and environ-
mental protection regulations.
No damaged products are assembled, installed or commissioned.
The necessary protective equipment is provided.
4.
Transport and place of erection
i
Immediately on receipt check the product for damage in transport. If the product is
damaged, do not install or commission it.
CAUTION
Improper transport to the place of erection
The workbench has a high tare weight - risk of injury if lifted improperly.
»
Wear foot protection and safety gloves.
»
Make sure the paths for movement and transport are clear.
»
At least two persons must be employed to transport the workbench to the erec-
tion location.
»
Ensure during movement and transport that all drawers and cupboard doors are
closed and locked.
Make sure that no components are damaged or destroyed during transport and
handling.
NOTICE
Improper transport
Damage due to improper transport.
»
Use only suitable lifting gear for transporting the workbench to the erection loca-
tion.
»
Do not attach lifting gear to the worktop in order to lift the workbench.
»
Do not pull the workbench across the floor.
»
Keep the workbench horizontal during transport.
»
Put the workbench down gently.
5.
Installation instructions
Trained specialist for mechanical work
5.1.
ACCESSORIES
When installing additional accessories, observe the relevant installation instructions.
6.
Installing the support leg and stabilising plates
i
Two persons working together turn the worktop over and place it on a flat and
clean support surface.
6.1.
SCOPE OF SUPPLY
Support leg
1 pc. support leg
3 pcs. hex wood screw Ø8 x 32 mm
3 pcs. washer Ø 8.4 mm
Stabilising plate
2 pcs. stabilising plate
4 pcs. hex wood screw
4 pcs. M6x12 hex screw
4 pcs. washer
4 pcs. cage nut
6.2.
SUPPORT LEG
A
www.hoffmann-group.com
de
bg
da
en
fi
fr
it
hr
lt
nl
no
pl
pt
ro
sv
sk
sl
es
cs
hu
21
Advertenties
Hoofdstukken
Inhoudsopgave
