Advertenties
Beschikbare talen
Beschikbare talen
•
Language
Using the navigation buttons (56), go to the
language that you require. After this, confirm
the settings you have made by pressing the
"OK" button (54). Confirm the message "Save
changes?" with the "OK" button (54) or press
the back button (55) to discard the change.
•
Multi-starting point
Where gardens have lots of angles, the robot
lawn mower may have problems reaching
every part of the lawn and mowing it comple-
tely. In this case you can select several star-
ting points on the perimeter wire (18). This will
enable the robot lawn mower to get to even
those parts of your garden that are difficult to
reach. The robot lawn mower will run the se-
lected distance along the perimeter wire (18)
and then start mowing in this part of the gar-
den (Fig. 9b). Use the navigation buttons (56)
to go to the point that you wish to change and
enter the distance and frequency accordingly.
The charging station (19) is automatically
defined as starting point 1. The two other st-
arting points can be selected as you wish. For
this you must measure the distance between
the charging station (19) and the starting
point in clockwise direction along the perime-
ter wire (18). With the frequency setting you
decide how often the robot lawn mower starts
its work from the charging station (19) or from
the respective starting points.
•
Information
This provides you with information about the
current software version of your robot lawn
mower
Mowing time settings
•
Operating time
This provides you with information about the
current settings of the operating times of your
robot lawn mower
•
Mowing edges
For a tidy lawn edge, the "Edge mowing" set-
ting can be activated. The robot lawn mower
starts its mowing work every 7 work days by
first mowing once along the entire perimeter
wire. In addition, the robot lawn mower mows
on the way to the charging station at the end
of the daily mowing interval, if the charge le-
vel of the rechargeable battery is over 70%.
•
Fault memory
This provides you with information about the
most recent fault messages of your robot
lawn mower.
Anl_FREELEXO_LCD_BT_SPK13.indb 40
Anl_FREELEXO_LCD_BT_SPK13.indb 40
GB
•
Mower statistics
This provides you with information about a
range of mower statistics.
Changing the PIN
You can change the PIN for the robot lawn mo-
wer and use your own personal PIN. To do so,
proceed as described in the chapter "Locking
mechanism / PIN". Important! Make a note of the
new PIN.
6.6 Control of the robot lawn mower
Starting procedure
1. Unlock the control panel (2).
2. Press the "START" button (52) fi rst.
3. Close the display cover (22).
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. The batte-
ry charge level is monitored during the work time
and displayed on the LCD-display (50). Whenever
the battery charge level drops to 30%, the robot
lawn mower automatically returns to the charging
station (19).
Stopping mowing
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Unlock the control panel (2).
3. Press the "HOME" button (53) to send the ro-
bot lawn mower along the perimeter wire (18)
and back to the charging station (19).
4. Close the display cover (22).
6.7 Control of the robot lawn mower using
the app
All settings that you can make using the control
panel can also be made using the app. To do
so, fi rst download the Einhell app for robot lawn
mowers to your smart phone. The Einhell app is
available via the following link and QR code:
iOS: http://qr.einhell.com/12e103ce
- 40 -
09.11.2021 14:54:51
09.11.2021 14:54:51
Advertenties
