Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
OBJ_BUCH-2992-002.book Page 12 Wednesday, September 6, 2017 11:43 AM
12 | English
17 Lid of the dust cup
18 Dust bag
19 Dust bag holder
20 Air diffuser
21 Fabric filter
22 Flat-pleated filter
23 Exhaust air cover
24 Permanent filter
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Dry vacuum cleaner
Article number
Rated voltage
Rated power input
Frequency
Container volume (gross)
Vacuum (turbine), max.
Airflow (turbine), max.
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
max. power
Rated voltage
EU/AUS
220–240 V
UK
220–240 V
* Specification of the allowable load of the connected power tool (coun-
try-specific)
Assembly
Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum Hose (see figure A)
– Insert the vacuum hose 10 into the hose connection piece
7 and turn it all the way in clockwise direction.
Mounting VAC Accessories
The vacuum hose 10 is equipped with a clip system, with
which the VAC accessories (extraction adapter 12, curved
nozzle 11) can be connected.
Fitting the extraction adapter or curved nozzle
(see figure B)
– Fit the extraction adapter 12 or the curved nozzle 11 to the
vacuum hose 10 until the two snap fasteners 15 of the vac-
uum hose click into place.
– To disassemble, press both snap-fasteners 15 inward and
pull the components apart.
1 609 92A 43U | (6.9.17)
Mounting the suction nozzles
– Then attach the required vacuuming accessory (floor noz-
zle, crevice nozzle, etc.) firmly to the curved nozzle 11 or
the extraction adapter 12.
Replacing/Inserting the Dust Bag
(see figures C1 – C4)
For vacuuming fine dust, which is generated when working
with sanders, drills or fine saw blades, you should use a dust
bag (accessory). This makes the dust easier to dispose of.
Chips, which are generated when working with larger saws, or
coarser dirt can be vacuumed without using a dust bag. When
doing so, you should clean the fabric filter 21 occasionally
(see "Cleaning the Filter Assembly", page 13).
EasyVac 3
Replacing/Inserting the Dust Bag (Accessory)
0 603 3D1 0..
– Press the release button 8 and pull the dust cup 9 out of
V
220–240
the vacuum cleaner.
W
700
– Grip the lid 17 at the connection flange 16 and remove the
lid from the dust cup.
Hz
50/60
– Turn the lid 17 over.
l
2.1
– Put the dust bag 18 over the connection flange 16 of the
mbar
240
vacuum cleaner and turn the cardboard flaps under the
l/s
35
dust bag holder 19.
– Press the lid 17 back onto the dust cup 9 and then slide the
dust cup back into the vacuum cleaner until it clicks into
kg
4.3
place.
/I
– To remove a full dust bag 18, twist it off the connection
flange 16 in a downward direction – without turning the
lid 17 over.
Operation
min. power
output
output
Before any work on the vacuum cleaner itself, pull the
2000 W
100 W
mains plug.
1800 W
100 W
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the vacuum cleaner. Equipment marked
with 230 V can also be operated with 220 V.
Only use an undamaged filter (no cracks, small holes,
etc.). Replace a damaged filter immediately.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
To save energy, only switch the vacuum cleaner on when us-
ing it.
To ensure optimal vacuuming performance, always complete-
ly unwind the vacuum hose 10 from the vacuum cleaner lid .
Vacuuming of deposited dust
– To switch on the vacuum cleaner, set the
mode selector switch 2 to the "Vacuuming"
symbol.
– To switch off the vacuum cleaner, set the
mode selector switch 2 to the "Off" symbol.
Bosch Power Tools
Advertenties
Inhoudsopgave
