Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
13. Cleaning
To clean the motor: To prevent stone dust from
collecting inside the wall chaser, you must
occasionally clean the motor by blowing
compressed air through the air duct on the back of
the motor housing, if the machine is used for
extended periods. If possible, this process should
NOT be carried out indoors/in a confined space.
Button (7) for adjusting the handle:
Occasionally blow compressed air through the
button (when pressed, in all 3 main handle
positions).
14. Troubleshooting
- Overload protection: The electronic signal
display (4) lights up and the load speed
decreases slightly. The machine is overloaded.
Work with a reduced load until the electronic
signal display goes out.
- Overload protection: The electronic signal
display (4) lights up and the load speed
decreases dramatically. The motor temperature
is too high! Run the machine in idling until it cools
down and the electronic signal display switches
off.
- Metabo S-automatic safety stop: The
electronic signal display (4) lights up and the
machine SWITCHES OFF automatically. If the
slew rate of the current is too high (for example, if
the machine suddenly seizes or kickback occurs),
the machine switches off. Switch off the machine
at the trigger (6). Switch it on again and continue
to work as normal. Try to prevent the machine
from seizing. See section 4.2.
- Restart protection: The electronic signal
display (4) FLASHES and the machine does
not start. The restart protection is active. If the
mains plug is inserted with the machine switched
on, or if the current supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 16.).
15. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
Metabo diamond cut-off wheels:
diameter 230 mm, laser-welded, suitable for dry
cutting, wheel thickness in the clamping range =
1.8 mm, bore = 22.23 mm, for wall chaser MFE 65
Application
for hard and medium-hard
materials (e.g. concrete,
including reinforced concrete)
for abrasive materials
(e.g. abrasive concrete, sandstone,
lime sand brick, aerated concrete
and similar materials)
16. Repairs
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
17. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
18. Technical Specifications
Explanation of details on page 3. Subject to
changes serving technical progress.
D
B
T
P1
P2
n
m
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
h
K
h
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given in EN
60745 and may be used to compare one tool with
another. It is also suitable for a provisional estimate
of the vibratory load.
The specified vibration level applies to the main
applications of the power tool. However, if the tool is
used for other applications, with different
Order no.
accessories or when poorly maintained, the
vibration level may vary. An estimation of the level of
exposure to vibration should also take into account
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
= Diameter of the diamond cut-off wheels
= Groove width options
= Adjustable depth of cut
= Nominal power input
= Power output
= No-load speed
= Weight without mains cable
= Vibration emission level
= Uncertainty (vibration)
ENGLISH en
6.28134
6.28145
15
Advertenties
Inhoudsopgave
